Toyota Tundra. Manual — part 1742
Fig. 28: Identifying Air Pump Inlet And Stopper
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Install the 2 bolts
Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf)
4
INSTALL AIR PUMP ASSEMBLY WITH BRACKET
a
Install the air pump to the vehicle
1
Insert the bracket tab into the slot and insert the stud bolt into the bracket hole as shown in
illustration A Then slide the bracket
Fig. 29: Locating Stud Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2
Insert the bracket tab into the slot shown in illustration B
3
Install the 2 bolts and 2 nuts
Torque: for bolt
18 N*m (184 kgf*cm, 13 ft.*lbf)
for nut
12 N*m (122 kgf*cm, 9 ft.*lbf)
b
Connect the 2 air pump connectors and attach the 3 wire harness claws
2009 Toyota Tundra
2009 ENG NE Emission Control (3UR-FBE) - Tundra
Fig. 30: Locating Air Pump Connectors
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
5
INSTALL NO. 3 AIR INJECTION SYSTEM HOSE
a
Connect the No 3 hose so that its paint mark aligns with the air pump's rib as shown in the
illustration below labeled A
b
Connect the clamp to the No 3 hose shown in the illustration below labeled B Then insert the
clamp's clip into the body hole
HINT:
Align the paint mark of the No 3 hose with the edge of the clamp
c
Connect the No 3 hose to the air tube shown in the illustration below labeled C
HINT:
Make sure the paint mark of the No 3 hose is facing upward
Make sure the direction of the hose clamp is as shown in the illustration
d
Connect the clamp to the No 3 hose and wire harness shown in the illustration below labeled D
Then insert the clamp's clip into the body hole
HINT:
Align the paint mark of the No 3 hose and paint mark of the wire harness with the edge of the
clamp
6
INSTALL NO. 2 AIR INJECTION SYSTEM HOSE
a
Connect the No 2 hose so that its paint mark aligns with the air pump's rib as shown in the
illustration below labeled E
b
Connect the No 2 hose to the air tube shown in the illustration below labeled F
HINT:
Make sure the paint mark of the No 2 hose is facing upward
Make sure the direction of the hose clamp is as shown in the illustration
2009 Toyota Tundra
2009 ENG NE Emission Control (3UR-FBE) - Tundra
c
Connect the white colored clamp to the No 2 hose and wire harness shown in the illustration below
labeled G
HINT:
Make sure the paint mark of the No 2 hose is facing upward
Make sure the direction of the hose clamp is as shown in the illustration
d
Connect the black colored clamp to the No 2 hose and wire harness shown in the illustration below
labeled H Then insert the clamp's clip into the body hole
Fig. 31: Identifying Paint Mark On Wire Harness
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
7
CONNECT FRONT FENDER APRON SEAL RH
a
Connect the fender apron seal with the 2 clips
2009 Toyota Tundra
2009 ENG NE Emission Control (3UR-FBE) - Tundra
Fig. 32: Connecting Fender Apron Seal With Clips
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
8
INSTALL FRONT FENDER LINER RH
a
Install the fender liner with the 9 clips
Fig. 33: Identifying Fender Liner And Clips
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
AIR SWITCHING VALVE
COMPONENTS
2009 Toyota Tundra
2009 ENG NE Emission Control (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст