Toyota Tundra. Manual — part 1970
Fig. 329: Locating Ring Pin
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3
INSTALL REAR CRANKSHAFT OIL SEAL
a
Using SST, tap in a new oil seal until its surface is flush with the oil seal retainer edge
SST 09223-15030, 09950-70010 (09951 -07100)
Standard depth:
0 to 1.0 mm (0 to 0.0394 in.)
4
INSTALL OIL DRAIN PIPE SUB-ASSEMBLY
a
Apply a light coat of engine oil to a new O-ring
NOTE:
Keep the lip free from foreign matter.
Do not tap on the oil seal at an angle.
Fig. 330: Tapping In Oil Seal
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
b
Install the O-ring to the drain pipe
c
Install the oil drain pipe with the bolt
Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
Fig. 331: Locating Oil Drain Pipe With Mounting Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
5
INSTALL ENGINE REAR OIL SEAL RETAINER
a
Apply seal packing in a continuous line as shown in the illustration
Seal packing:
Toyota Genuine Seal Packing Black, Three
Bond 1207B or equivalent
Seal diameter:
2.0 to 3.0 mm (0.0787 to 0.118 in.)
Application position from inside edge of retainer:
3.5 mm (0.138 in.)
Fig. 332: Identifying Seal Packing Areas On Engine Rear Oil Seal Retainer
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Install the oil seal retainer with the 6 bolts
Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
6
INSTALL OIL STRAINER SUB-ASSEMBLY
a
Apply a light coat of engine oil to a new O-ring
b
Install the O-ring to the oil strainer
c
Install the oil strainer with the 2 bolts
Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
NOTE:
Remove any oil from the contact surface.
Install the engine rear oil seal retainer within 3 minutes and
tighten the bolts and nuts within 15 minutes after applying seal
packing.
NOTE:
Do not start the engine for at least 2 hours after installing.
When installing the oil seal retainer, make sure the lip of the oil
seal is not damaged.
When installing the oil seal retainer, make sure the lip of the oil
seal is not folded incorrectly.
Fig. 333: Locating Oil Seal Retainer With Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NOTE:
Make sure the O-ring is not twisted or damaged.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Fig. 334: Locating Oil Strainer With Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
7
INSTALL NO. 1 OIL PAN BAFFLE PLATE
a
Install the baffle plate with the 7 bolts
Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
Fig. 335: Locating Baffle Plate With Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
8
INSTALL NO. 1 OIL PAN SUB-ASSEMBLY
a
Apply seal packing in a continuous line as shown in the illustration
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Standard seal diameter:
3.0 to 4.0 mm (0.118 to 0.157 in.)
NOTE:
Remove any oil from the contact surface.
Install the oil pan within 3 minutes and tighten the bolts and
nuts within 15 minutes after applying seal packing.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст