Toyota Tundra. Manual — part 1843
below
1
Check the A/F sensor (see REMOVAL ) and heated oxygen sensor (see ON-VEHICLE
INSPECTION ) operation
2
See the table below for possible causes, and then inspect and correct the applicable causes if
necessary
SYMPTOM TABLE
DRIVE BELT
COMPONENTS
CO
HC
Symptom
Cause
Normal High Rough idle
1
Faulty ignitions:
Incorrect timing
Plugs (contaminated, shorted or gaps
are defective)
2
Incorrect valve clearance
3
Leaky intake and exhaust valves
4
Leaky cylinder
Low High
Rough idle (Fluctuating HC
reading)
1
Vacuum leaks:
PCV hose
Intake manifold
Throttle body
Brake booster line
2
Lean mixture causing misfire
High High
Rough idle (Black smoke
from exhaust)
1
Restricted air filter
2
Faulty SFI system:
Faulty pressure regulator
Defective ECT sensor
Faulty ECM
Faulty injectors
Faulty throttle position sensor
Faulty MAF meter
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (2UZ-FE) - Tundra
Fig. 7: Identifying Drive Belt Replacement Components With Torque Specifications
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
ON-VEHICLE INSPECTION
1
INSPECT FAN AND GENERATOR V BELT
a
Visually check the belt for excessive wear, frayed cords, etc
If any defect has been found, replace the belt
HINT:
Cracks on the rib side of a belt are considered acceptable If the belt has chunks missing from the
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (2UZ-FE) - Tundra
ribs, it should be replaced
Fig. 8: Identifying Belt Excessive Wear
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Check by hand that the belt fits properly in the ribbed grooves and has not slipped out of the
grooves on the bottom of the pulley
Fig. 9: Identifying Belt Correct And Incorrect Position
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2
INSPECT V-RIBBED BELT TENSIONER ASSEMBLY
a
Check that the belt tensioner moves downward when the belt is pressed down at the point indicated
below with approximately 98 N (10 kgf, 22 0 lbf) of force
Fig. 10: Checking Belt Tensioner
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Check that the arrow on the belt tensioner is within area "A"
If it is outside area "A", replace the fan and generator V belt
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (2UZ-FE) - Tundra
HINT:
When a new belt is installed, the arrow should be within area "B" If not, the fan and generator V
belt is not installed correctly
Fig. 11: Identifying Belt Tensioner Area
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REMOVAL
1
REMOVE THROTTLE BODY COVER SUB-ASSEMBLY (See REMOVAL )
2
REMOVE AIR CLEANER HOSE ASSEMBLY (See REMOVAL )
3
REMOVE NO. 1 ENGINE UNDER COVER (See REPLACEMENT )
4
REMOVE FAN AND GENERATOR V BELT
a
Loosen the belt tension by turning the belt tensioner counterclockwise, and then remove the fan and
generator V belt
HINT:
The pulley bolt for the belt tensioner has left-hand thread
Fig. 12: Loosening Belt Tension
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSTALLATION
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (2UZ-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст