Toyota Tundra. Manual — part 1841
Fig. 455: Supporting Transmission With Transmission Jack
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2
REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
a
Remove the 4 bolts of the rear No 3 engine mounting insulator
Fig. 456: Locating Rear No. 3 Engine Mounting Insulator Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Remove the 4 nuts, 4 bolts, 4 plate washers and crossmember
Fig. 457: Locating No. 3 Frame Crossmember Nuts, Washers And Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3
REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR
a
Remove the 4 bolts and engine mounting insulator from the transmission
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (1GR-FE) - Tundra
Fig. 458: Locating Rear No. 1 Engine Mounting Insulator Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSTALLATION
1
SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY
a
Support the transmission with a transmission jack Lift the transmission slightly off of the
crossmember
Fig. 459: Supporting Transmission With Transmission Jack
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2
INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR
a
Install the engine mounting insulator to the transmission with the 4 bolts
Torque: 40 N*m (408 kgf*cm, 30 ft.*lbf)
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (1GR-FE) - Tundra
Fig. 460: Locating Rear No. 1 Engine Mounting Insulator Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3
INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
a
Install the frame crossmember to the engine rear mounting insulator with the 4 bolts
Torque: 16 N*m (63 kgf*cm, 12 ft.*lbf)
Fig. 461: Identifying Frame Crossmember To Rear Engine Mounting Insulator With Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Install the frame crossmember with the 4 bolts, 4 plate washers and 4 nuts
Torque: 110 N*m (1122 kgf*cm, 81 ft.*lbf)
Fig. 462: Identifying Frame Crossmember With Bolts, Washers And Nuts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (1GR-FE) - Tundra
2009 ENGINE
Engine Mechanical (2UZ-FE) - Tundra
ENGINE
ON-VEHICLE INSPECTION
1
INSPECT IGNITION TIMING
a
Warm up and stop the engine
1
Allow the engine to warm up to a normal operating temperature
b
When using the Techstream:
1
Connect the Techstream to the DLC3
2
Start the engine and idle it
3
Push the Techstream main switch ON
4
Enter the following menus: Powertrain/Engine and ECT/Data List/Primary/IGN Advance
HINT:
Refer to the Techstream operator's manual for further details
Standard ignition timing: 5 to 15° BTDC @ idling (transmission in neutral and A/C
switch OFF)
5
Disconnect the Techstream from the DLC3
c
When not using the Techstream:
1
Connect the tester probe of a timing light to the wire of the ignition coil connector for the No
1 cylinder
Fig. 1: Identifying Tester Probe Of Timing Light
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NOTE:
Use a timing light that detects primary signals.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (2UZ-FE) - Tundra
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (2UZ-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст