Toyota Tundra. Manual — part 1588
DTC P060B INTERNAL CONTROL MODULE A/D PROCESSING PERFORMANCE
DESCRIPTION
This DTC is output when a communication error occurs in the ECM.
DTC DETECTION CONDITION AND TROUBLE AREA REFERENCE CHART
MONITOR STRATEGY
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
TYPICAL MALFUNCTION THRESHOLDS CONDITIONS
INSPECTION PROCEDURE
1. CHECK DTC
a. Clear DTC (See DTC CHECK/CLEAR ).
b. Turn the ignition switch off.
c. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
d. Connect the cable to the negative (-) battery terminal.
e. Turn the ignition switch to ON.
f. Check DTC.
DTC
DTC Detection Condition
Trouble Area
P060B
ECM main CPU communication
error
ECM
Related DTCs
None
Required sensors/components (main)
ECM
Required sensors/components (sub)
-
Frequency of operation
Once per driving cycle
Duration
16 seconds
MIL operation
Immediate
Sequence of operation
None
Monitor runs whenever the following DTCs are not present
None
When one of following conditions is met
Condition 1, 2 or 3
1. Internal control module serial communication
Fail
2. AD converter
Fail
3. Knock sensor circuit
Fail
2009 Toyota Tundra
2009 ENGINE PERFORMANCE Engine Control System (3UR-FBE) - Tundra
Result
DTC OUTPUT RESULT
B: REPLACE ECM (See REMOVAL )
C: GO TO DTC (P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D) (See DTC
P0327 KNOCK SENSOR 1 CIRCUIT LOW INPUT (BANK 1 OR SINGLE SENSOR); DTC
P0328 KNOCK SENSOR 1 CIRCUIT HIGH INPUT (BANK 1 OR SINGLE SENSOR); DTC
P032C KNOCK SENSOR 3 CIRCUIT LOW; DTC P032D KNOCK SENSOR 3 CIRCUIT
HIGH; DTC P0332 KNOCK SENSOR 2 CIRCUIT LOW INPUT (BANK 2); DTC P0333
KNOCK SENSOR 2 CIRCUIT HIGH INPUT (BANK 2); DTC P033C KNOCK SENSOR 4
CIRCUIT LOW INPUT; DTC P033D KNOCK SENSOR 4 CIRCUIT HIGH INPUT )
A: CHECK FOR INTERMITTENT PROBLEMS (See CHECK FOR INTERMITTENT
PROBLEMS )
DTC P060D INTERNAL CONTROL MODULE ACCELERATOR PEDAL POSITION
PERFORMANCE
DESCRIPTION
The ECM monitors the input signals of the Accelerator Pedal Position (APP) sensor No. 1. When the input
signals and control signals are deviated, a DTC is output.
DTC DETECTION CONDITION AND TROUBLE AREA REFERENCE CHART
MONITOR STRATEGY
MONITOR STRATEGY
Result
Proceed
to
DTC is not output
A
DTC P060B is output
B
DTC P060B and P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D are
output
C
DTC
DTC Detection Condition
Trouble Area
P060D
When either condition below is
met
ECM main CPU error
ECM sub CPU error
ECM
Related DTCs
None
Required sensors/components (main)
ECM
Required sensors/components (sub)
-
2009 Toyota Tundra
2009 ENGINE PERFORMANCE Engine Control System (3UR-FBE) - Tundra
TYPICAL ENABLING CONDITIONS
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
TYPICAL MALFUNCTION THRESHOLDS CONDITIONS
INSPECTION PROCEDURE
1. CHECK DTC
a. Clear DTC (See DTC CHECK/CLEAR ).
b. Turn the ignition switch off.
c. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
d. Connect the cable to the negative (-) battery terminal.
e. Turn the ignition switch to ON.
f. Check DTC.
OK:
P060D is not present.
NG: REPLACE ECM (See REMOVAL )
OK: CHECK FOR INTERMITTENT PROBLEMS (See CHECK FOR INTERMITTENT
PROBLEMS )
DTC P060E INTERNAL CONTROL MODULE THROTTLE POSITION PERFORMANCE
DESCRIPTION
The ECM monitors the input signals of the Throttle Position (TP) sensor No. 1 and stop light switch. As the
ECM monitors the input signals of the TP sensor No. 1 and the STP signals of the stop light switch, if the input
signals and control signals are deviated, a DTC is output.
DTC DETECTION CONDITION AND TROUBLE AREA REFERENCE CHART
Frequency of operation
Once per driving cycle
Duration
1 second
MIL operation
Immediate
Sequence of operation
None
Monitor runs whenever following DTCs not present
None
Difference of main APP and sub APP
0.3 V or more
DTC
DTC Detection Condition
Trouble Area
2009 Toyota Tundra
2009 ENGINE PERFORMANCE Engine Control System (3UR-FBE) - Tundra
MONITOR STRATEGY
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
TYPICAL MALFUNCTION THRESHOLDS CONDITIONS
INSPECTION PROCEDURE
1. CHECK DTC
a. Clear DTC (See DTC CHECK/CLEAR ).
b. Turn the ignition switch off.
c. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
d. Connect the cable to the negative (-) battery terminal.
e. Turn the ignition switch to ON.
f. Check DTC.
OK:
P060E is not present.
P060E
When either condition below is
met
ECM main CPU error
ECM sub CPU error
ECM
Related DTCs
None
Required sensors/components (main)
ECM
Required sensors/components (sub)
-
Frequency of operation
Once per driving cycle
Duration
1 second
MIL operation
Immediate
Sequence of operation
None
Monitor runs whenever following DTCs not present
None
DMA communication error
Not detected
When one of following conditions is met
Condition 1 or 2
1. Difference of main TP and sub TP
0.3 V or more
2. Difference of main brake switch signal and sub brake switch signal
Different
2009 Toyota Tundra
2009 ENGINE PERFORMANCE Engine Control System (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст