Toyota Tundra. Manual — part 1587
CONFIRMATION DRIVING PATTERN".
HINT
If no exhaust gas leaks are present, a malfunction in the heated oxygen sensor circuit is
suspected.
If any exhaust gas leaks are present around the heated oxygen sensor, noise appears in the
output voltage of the heated oxygen sensor.
4. PERFORM CONFIRMATION DRIVING PATTERN
Fig. 201: Vehicle Driving Pattern
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Connect the Techstream to the DLC3.
b. Clear DTC (See DTC CHECK/CLEAR ).
HINT
Even if no DTCs are stored, perform the DTC clear operation to start alcohol concentration
learning.
c. Start the engine.
HINT
After clearing the DTCs, the engine may become difficult to start if the concentration of alcohol in
the fuel is high. Therefore, it may be necessary to crank the engine a few times before it starts.
d. Warm up the engine until the engine coolant temperature becomes 75°C (167°F) or more.
e. Drive the vehicle at 32 km/h (20 mph) or more for 2 minutes.
f. After this driving make sure that the Data List "Alcohol Density Learning" is "Compl".
g. Perform the drive pattern.
1. Accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle.
2. Drive the vehicle between 60 and 80 km/h (35 and 50 mph) for 5 minutes.
h. Enter the following menu Powertrain/Engine and ECT/Trouble Codes.
i. Read the DTCs.
2009 Toyota Tundra
2009 ENGINE PERFORMANCE Engine Control System (3UR-FBE) - Tundra
Result
DTC OUTPUT RESULT
B: REPLACE ECM (See REMOVAL )
C: Go to step 6
A: Go to Next Step
5. INSPECT DTC (P0136, P0137, P0138, P0156, P0157 OR P0158)
a. Inspect the P0136, P0137, P0138, P0156, P0157 or P0158 flowchart.
HINT
If P0136 or P0156 is output, troubleshoot for that DTC first (See DTC P0136 OXYGEN
SENSOR CIRCUIT MALFUNCTION (BANK 1 SENSOR 2); DTC P0137 OXYGEN
SENSOR CIRCUIT LOW VOLTAGE (BANK 1 SENSOR 2); DTC P0138 OXYGEN
SENSOR CIRCUIT HIGH VOLTAGE (BANK 1 SENSOR 2); DTC P0139 OXYGEN
SENSOR CIRCUIT SLOW RESPONSE (BANK 1 SENSOR 2); DTC P0156 OXYGEN
SENSOR CIRCUIT MALFUNCTION (BANK 2 SENSOR 2); DTC P0157 OXYGEN
SENSOR CIRCUIT LOW VOLTAGE (BANK 2 SENSOR 2); DTC P0158 OXYGEN
SENSOR CIRCUIT HIGH VOLTAGE (BANK 2 SENSOR 2); DTC P0159 OXYGEN
SENSOR CIRCUIT SLOW RESPONSE (BANK 2 SENSOR 2) ). Then proceed to "6
INSPECT ECM".
If P0137 or P0157 is output, troubleshoot for that DTC first (See DTC P0136 OXYGEN
SENSOR CIRCUIT MALFUNCTION (BANK 1 SENSOR 2); DTC P0137 OXYGEN
SENSOR CIRCUIT LOW VOLTAGE (BANK 1 SENSOR 2); DTC P0138 OXYGEN
SENSOR CIRCUIT HIGH VOLTAGE (BANK 1 SENSOR 2); DTC P0139 OXYGEN
SENSOR CIRCUIT SLOW RESPONSE (BANK 1 SENSOR 2); DTC P0156 OXYGEN
SENSOR CIRCUIT MALFUNCTION (BANK 2 SENSOR 2); DTC P0157 OXYGEN
SENSOR CIRCUIT LOW VOLTAGE (BANK 2 SENSOR 2); DTC P0158 OXYGEN
SENSOR CIRCUIT HIGH VOLTAGE (BANK 2 SENSOR 2); DTC P0159 OXYGEN
SENSOR CIRCUIT SLOW RESPONSE (BANK 2 SENSOR 2) ). Then proceed to "6
INSPECT ECM".
If P0138 or P0158 is output, troubleshoot for that DTC first (See DTC P0136 OXYGEN
SENSOR CIRCUIT MALFUNCTION (BANK 1 SENSOR 2); DTC P0137 OXYGEN
SENSOR CIRCUIT LOW VOLTAGE (BANK 1 SENSOR 2); DTC P0138 OXYGEN
SENSOR CIRCUIT HIGH VOLTAGE (BANK 1 SENSOR 2); DTC P0139 OXYGEN
SENSOR CIRCUIT SLOW RESPONSE (BANK 1 SENSOR 2); DTC P0156 OXYGEN
SENSOR CIRCUIT MALFUNCTION (BANK 2 SENSOR 2); DTC P0157 OXYGEN
SENSOR CIRCUIT LOW VOLTAGE (BANK 2 SENSOR 2); DTC P0158 OXYGEN
Result
Proceed to
P0136, P0137, P0138, P0156, P0157, P0158 and/or P0607
A
Only P0607
B
No DTC output
C
2009 Toyota Tundra
2009 ENGINE PERFORMANCE Engine Control System (3UR-FBE) - Tundra
SENSOR CIRCUIT HIGH VOLTAGE (BANK 2 SENSOR 2); DTC P0159 OXYGEN
SENSOR CIRCUIT SLOW RESPONSE (BANK 2 SENSOR 2) ). Then proceed to "6
INSPECT ECM".
If DTC P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output, the output
voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or
more).
6. INSPECT ECM
a. Connect the Techstream to the DLC3.
b. Clear DTC (See DTC CHECK/CLEAR ).
c. Stop the engine and wait for 30 minutes.
d. Start the engine and allow it to idle for 2 minutes.
e. Enter the following menus Powertrain/Engine and ECT/Trouble Codes.
f. Check the DTCs.
Result
DTC OUTPUT RESULT
B: REPLACE ECM (See REMOVAL )
A: END
DTC P060A INTERNAL CONTROL MODULE MONITORING PROCESSOR PERFORMANCE
DESCRIPTION
The main CPU and sub CPU of the ECM perform data communication between each other. The main CPU
monitors the communications and WDC pulses from the sub CPU. When the signal malfunctions below are
detected, a DTC is output.
DTC DETECTION CONDITION AND TROUBLE AREA REFERENCE CHART
MONITOR STRATEGY
Result
Proceed to
DTC is not output
A
P0607 is output
B
DTC
DTC Detection Condition
Trouble Area
P060A
When either condition below is
met
ECM main CPU error
ECM sub CPU error
Electronic throttle
monitoring CPU error
ECM
2009 Toyota Tundra
2009 ENGINE PERFORMANCE Engine Control System (3UR-FBE) - Tundra
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
TYPICAL MALFUNCTION THRESHOLDS CONDITIONS
INSPECTION PROCEDURE
1. CHECK DTC
a. Clear DTC (See DTC CHECK/CLEAR ).
b. Turn the ignition switch off.
c. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
d. Connect the cable to the negative (-) battery terminal.
e. Turn the ignition switch to ON.
f. Check DTC.
OK:
P060A is not present.
NG: REPLACE ECM (See REMOVAL )
OK: CHECK FOR INTERMITTENT PROBLEMS (See CHECK FOR INTERMITTENT
PROBLEMS )
Related DTCs
None
Required sensors/components (main)
ECM
Required sensors/components (sub)
-
Frequency of operation
Once per driving cycle
Duration
16 seconds
MIL operation
Immediate
Sequence of operation
None
Monitor runs whenever the following DTCs are not present
None
CPU reset
Occurred
When either condition below is met
Condition 1 or 2
1. When all conditions below are met
-
CPU reset
1 time or more
Learned TP - Learned APP
0.4 V or more
Electronic throttle actuator
OFF
2. CPU reset
2 times or more
2009 Toyota Tundra
2009 ENGINE PERFORMANCE Engine Control System (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст