Toyota Tundra. Manual — part 2301
Fig. 94: Locating Fluid Coupling Bracket Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
j
Temporarily install the belt tensioner with the standard bolt and 6 mm hexagon bolt
Fig. 95: Locating Belt Tensioner Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
k
Tighten the 8 bolts labeled 4 to 11 in several steps in the sequence shown in the illustration
Torque: 47 N*m (479 kgf*cm, 35 ft.*lbf)
Item
Length
Thread Diameter
Bolt A 70 mm (2 76 in ) 8 mm (0 315 in )
Bolt B 80 mm (3 15 in ) 10 mm (0 394 in )
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FBE) - Tundra
Fig. 96: Locating Bolts Tightening Sequence
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
l
Tighten the 23 bolts and nut labeled 12 to 35 in several steps in the sequence shown in the
illustration
Torque: 23 N*m (235 kgf*cm, 17 ft.*lbf)
Fig. 97: Locating Bolts Tightening Sequence
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Fig. 98: Identifying Seal Packing Restriction Area
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3
INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
a
Install 5 new gaskets to the camshaft bearing caps (No 2, No 3)
NOTE:
After the installation, if the seal packing has seeped out at the areas
labeled A shown in the illustration, wipe it off.
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FBE) - Tundra
Fig. 99: Locating Camshaft Bearing Cap Gaskets
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Install the gasket to the cylinder head cover
c
Apply seal packing as shown in the illustration
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
d
Install the cylinder head cover washer with a new seal and the 14 bolts
Torque: for bolt A
21 N*m (214 kgf*cm, 15 ft.*lbf)
NOTE:
Remove any oil from the contact surface.
NOTE:
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten the
bolts within 15 minutes after applying seal packing.
Fig. 100: Locating Seal Packing Applying Areas
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FBE) - Tundra
except bolt A
12 N*m (122 kgf*cm, 9 ft.*lbf)
Fig. 101: Locating Cylinder Head Cover Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
4
INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH
a
Install 5 new gaskets to the camshaft bearing caps (No 1, No 3)
Fig. 102: Locating Camshaft Bearing Cap Gaskets
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Install the gasket to the cylinder head cover
c
Apply seal packing as shown in the illustration
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
NOTE:
Do not start the engine for at least 2 hours after the installation.
NOTE:
Remove any oil from the contact surface.
NOTE:
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст