Toyota Tundra. Manual — part 705
OK: Go to Next Step
4. INSPECT IGNITION SWITCH
a. Remove the ignition switch.
1. For 1GR-FE, refer to the following procedures (see INSPECTION ).
2. For 2UZ-FE, refer to the following procedures (see INSPECTION ).
3. For 3UR-FE, refer to the following procedures (see INSPECTION ).
4. For 3UR-FBE, refer to the following procedures (see INSPECTION
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
IGNITION SWITCH
Fig. 18: Identifying Ignition Switch Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Result
STANDARD RESISTANCE RESULT CHART
B: REPLACE IGNITION SWITCH (See REMOVAL )
C: REPLACE IGNITION SWITCH (See REMOVAL )
D: REPLACE IGNITION SWITCH (See REMOVAL )
Tester Connection Switch Condition Specified Condition
1 (IG1) - 4 (AM1) Ignition switch ON
Below 1 ohms
Result
Proceed to
OK
A
NG (for 1GR-FE)
B
NG (for 2UZ-FE)
C
NG (for 3UR-FE)
D
NG (for 3UR-FBE)
E
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Theft Deterrent - Tundra
E: REPLACE IGNITION SWITCH (See REMOVAL
A: Go to Next Step
5. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - IGNITION SWITCH AND BODY
GROUND)
a. Disconnect the DD main body ECU connector.
b. Disconnect the J9 ignition switch connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
MAIN BODY ECU - IGNITION SWITCH AND BODY GROUND
Fig. 19: Checking Harness And Connector (Main Body ECU - Ignition Switch And Body
Ground)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
Tester Connection Condition Specified Condition
DD-47 - J9-4(AM1)
Always
Below 1 ohms
DD-43 - J9-1 (IG1)
DD-62 - Body ground
DD-47 - Body ground
Always
10 kohms or higher
DD-43 - Body ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Theft Deterrent - Tundra
OK: REPLACE MAIN BODY ECU
GLASS BREAKAGE SENSOR ECU CIRCUIT
DESCRIPTION
When the glass breakage sensor detects the glass is broken (1st time), the sensor will set off an alarm for 20
seconds (pre-alarm). If the glass breakage sensor detects that more glass is broken (2nd time or more), the
sensor will set off an alarm for 60 seconds.
WIRING DIAGRAM
Fig. 20: Glass Breakage Sensor ECU - Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. READ VALUE OF TECHSTREAM (GLASS BREAKAGE SENSOR)
a. Using Techstream, read the Data List.
Techstream
MAIN BODY
TECHSTREAM MAIN BODY REFERENCE CHART
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic
Note
ON: Glass breakage
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Theft Deterrent - Tundra
OK: When tapping on the door glass with your finger, "ON" is displayed on the
Techstream screen.
NG: Go to step 2
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE
2. INSPECT FUSE (ECU-IG No. 1)
a. Remove the ECU-IG No. 1 fuse from the main body ECU.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
FUSE (ECU-IG No. 1)
NG: REPLACE FUSE
OK: Go to Next Step
3. CHECK HARNESS AND CONNECTOR (GLASS BREAKAGE SENSOR ECU - BATTERY AND
BODY GROUND)
a. Disconnect the J57 glass breakage sensor ECU connector.
b. Measure the voltage and resistance according to the value(s) in the table below.
Standard voltage
GLASS BREAKAGE SENSOR ECU - BATTERY AND BODY GROUND VOLTAGE
Standard resistance
GLASS BREAKAGE SENSOR ECU - BATTERY AND BODY GROUND RESISTANCE
Glass Break Sensor
Detection
Glass breakage sensor
detection / ON or OFF
sensor ON
OFF: Glass breakage
sensor OFF
-
Tester Connection Condition Specified Condition
ECU-IG No. 1 fuse Always
Below 1 ohms
Tester Connection
Switch Condition Specified Condition
J57-2 (GB+B) - J57-6 (GND)
Always
11 to 14 V
J57-3 (GBIG) - J57-6 (GND)
Ignition switch ON
11 to 14 V
Ignition switch OFF
Below 1 V
Tester Connection
Condition Specified Condition
J57-6 (GND) - Body ground Always
Below 1 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Theft Deterrent - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст