Toyota Tundra. Manual — part 748
Fig. 127: Identifying Double Sided Tape On Upper Outside Back Window Moulding (For Slide
Type)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
HINT:
Perform the following procedure if replacing the back window moulding.
a. Using a moulding remover, detach the 3 clips and remove the back window moulding.
28. REMOVE LOWER OUTSIDE BACK WINDOW MOULDING (for Slide Type)
Fig. 128: Identifying Double Sided Tape On Lower Outside Back Window Moulding (For Slide
Type)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
HINT:
Perform the following procedure if replacing the back window moulding.
a. Using a moulding remover, detach the 3 clips and remove the back window moulding.
29. CLEAN BACK WINDOW ASSEMBLY
a. Using a scraper, remove the damaged spacers and adhesive sticking to the glass.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Fig. 129: Removing Damaged Stoppers, Dams And Adhesive Sticking To Glass
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Clean the outer edge of the back window with a non-residue solvent.
30. CLEAN VEHICLE BODY
a. Using a scraper, remove the moulding and adhesive from the vehicle body.
b. Clean and shape the contact surface of the vehicle body.
1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown
in the illustration.
Fig. 130: Identifying Excess Adhesive
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
HINT:
Leave as much adhesive on the vehicle body as possible.
NOTE:
Do not touch the back window surface after cleaning it.
Be careful not to damage the window.
Even if using a new back window, clean the back window with a
non-residue solvent.
NOTE:
Be careful not to damage the vehicle body.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
2. Clean the contact surface of the vehicle body with cleaner.
HINT:
Even if all the adhesive has been removed, clean the vehicle body.
INSTALLATION
1. INSTALL NO. 1 BACK WINDOW GLASS SPACER
a. Install 2 new spacers onto the back window assembly as shown in the illustration.
Fig. 131: Identifying Spacers Onto Back Window Glass Assembly
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. INSTALL NO. 2 BACK WINDOW GLASS SPACER
a. Install 2 new spacers onto the back window assembly as shown in the illustration.
Fig. 132: Identifying Spacers Onto Back Window Glass Assembly
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3. INSTALL BACK WINDOW ASSEMBLY
a. Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.
NOTE:
Allow the primer to dry for 3 minutes or more.
Do not apply primer to the adhesive.
Throw away any leftover primer.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Fig. 133: Applying Primer M To Exposed Part Of Vehicle Body
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Using a brush or sponge, apply Primer G to the contact surface of the back window.
Fig. 134: Identifying Applying Area Of Primer G To Contact Surface Of Back Window
(Backside For Fixed Type)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Do not apply too much primer.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст