Toyota Tundra. Manual — part 1062
HINT:
Use the same removal procedure for both the front and rear propeller shaft universal joint spider bearings.
a. Place matchmarks on the flange yoke and shaft.
Fig. 84: Identifying Matchmarks On Flange Yoke And Shaft
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Remove the grease fitting from the spider bearing.
c. Using a brass bar and hammer, slightly tap in the 4 spider bearings.
Fig. 85: Tapping Spider Bearings
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
d. Using needle-nose pliers, remove the 4 snap rings from the grooves.
Fig. 86: Removing Snap Ring
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 DRIVELINE/AXLES Propeller Shaft - Tundra
e. Using a screwdriver, remove the 4 slingers of the spider bearing.
Fig. 87: Removing Slingers Of Spider Bearing
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
f. Clamp the shaft in a vise between aluminum plates.
g. Using SST, pull out the universal joint spider bearing from the shaft.
SST 09331-60010,09950-40011 (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09957-
04010, 09958-04011), 09955-04100
Fig. 88: Pulling Universal Joint Spider Bearing From Shaft
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
h. Clamp the protruding universal joint spider bearing in a vise.
i. Using a brass bar and hammer, tap the shaft yoke to remove the universal joint spider bearing.
NOTE:
Pull out the spider bearing until the SST claws contact the shaft's
universal joint yoke.
NOTE:
Do not tap the shaft tube.
2009 Toyota Tundra
2009 DRIVELINE/AXLES Propeller Shaft - Tundra
HINT:
Use the same removal procedure for the universal joint spider bearing on the opposite side.
Fig. 89: Identifying Hammering Point Location
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
j. Using SST, pull out the universal joint spider bearing from the flange yoke.
SST 09331-60010,09950-40011 (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09957-
04010, 09958-04011), 09955-04100
NOTE:
Pull out the spider bearing until the SST claws contact the flange
yoke.
2009 Toyota Tundra
2009 DRIVELINE/AXLES Propeller Shaft - Tundra
Fig. 90: Pulling Universal Joint Spider Bearing
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
k. Clamp the protruding universal joint spider bearing in a vise.
l. Using a brass bar and hammer, tap the flange yoke to remove the universal joint spider bearing.
HINT:
Use the same removal procedure for the universal joint spider bearing on the opposite side.
Fig. 91: Identifying Hammering Point Location
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
m. Remove the spider from the flange yoke.
INSPECTION
1. INSPECT PROPELLER SHAFT ASSEMBLY (for 2 Joint Type)
a. Using a dial indicator, measure the propeller shaft runout.
Maximum runout:
1.02 mm (0.0402 in.)
If the shaft runout is greater than the maximum, replace the propeller shaft assembly.
2009 Toyota Tundra
2009 DRIVELINE/AXLES Propeller Shaft - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст