Toyota Tundra. Manual — part 230
Fig. 272: Identifying W2 Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE TELEVISION DISPLAY (see REMOVAL )
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE (see PROBLEM SYMPTOMS TABLE )
MUTE SIGNAL CIRCUIT BETWEEN RADIO RECEIVER AND TELEVISION DISPLAY
ASSEMBLY
DESCRIPTION
The radio receiver controls the volume according to the mute signal from the television display.
WIRING DIAGRAM
Fig. 273: Mute Signal Circuit Between Radio Receiver And Television Display Assembly - Wiring
Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY - NAVIGATION
RECEIVER)
a. Disconnect the W2 display connector.
b. Disconnect the K22 receiver connector.
ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
Fig. 274: Identifying W2 And K22 Connectors Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OK: Go to next step.
2. CHECK TELEVISION DISPLAY
a. Reconnect the W2 display connector.
b. Measure the voltage according to the value(s) in the table below.
Standard voltage
TESTER CONNECTION SPECIFIED CONDITION
Tester Connection
Condition Specified Condition
W2-26 (MUTE) - K22-6 (MUTE) Always
Below 1 ohms
W2-26 (MUTE) - Body ground
Always
10 kohms or higher
Tester Connection
Switch Condition
Specified Condition
W2-26 (MUTE) - Body Ignition switch ACC, television display is
3.5 V or higher -->
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
NG: REPLACE TELEVISION DISPLAY (see REMOVAL )
Fig. 275: Identifying W2 Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE (see PROBLEM SYMPTOMS TABLE )
MUTE SIGNAL CIRCUIT BETWEEN NAVIGATION RECEIVER ASSEMBLY AND TELEVISION
DISPLAY ASSEMBLY
DESCRIPTION
The navigation receiver controls the volume according to the mute signal the television display. The mute signal
is sent to reduce noise and popping sound generated switching the mode, etc.
WIRING DIAGRAM
Fig. 276: Mute Signal Circuit Between Navigation Receiver Assembly And Television Display Assembly -
Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY - NAVIGATION
RECEIVER)
a. Disconnect the W2 display connector.
ground
playing --> Changing modes
Below 1 V
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
b. Disconnect the K8 receiver connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
Fig. 277: Identifying W2 And K8 Connectors Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OK: Go to next step.
2. CHECK TELEVISION DISPLAY
a. Reconnect the W2 display connector.
b. Measure the voltage according to the value(s) in the table below.
Standard voltage
TESTER CONNECTION SPECIFIED CONDITION
Tester Connection
Condition Specified Condition
W2-26 (MUTE) - K8-6 (MUTE) Always
Below 1 ohms
W2-26 (MUTE) - Body ground
Always
10 kohms or higher
Tester Connection
Switch Condition
Specified Condition
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст