Toyota Tundra. Manual — part 228
OK: It is not depleted.
NG: REPLACE REMOTE CONTROLLER BATTERY
OK: Go to next step.
3. CLEAN INFRARED RAY EMITTING PORTION
a. Clean the infrared ray emitting portion.
1. Clean the infrared ray emitting portion on the rear display.
2. Check whether the same malfunction occurs.
OK: The function returns to normal.
NG: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE (see PROBLEM SYMPTOMS TABLE )
Fig. 263: Locating Infrared Ray Emitting Portion
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OK: END
SOUND SIGNAL CIRCUIT BETWEEN RADIO RECEIVER AND TELEVISION DISPLAY
ASSEMBLY
DESCRIPTION
This circuit sends a sound signal from the television display to the radio receiver.
WIRING DIAGRAM
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Fig. 264: Sound Signal Circuit Between Radio Receiver And Television Display Assembly - Wiring
Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
1. INSPECTION PROCEDURE
a. Disconnect the W2 display connector.
b. Disconnect the K22 receiver connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
Tester Connection
Condition Specified Condition
W2-28 (R+) - K22-2 (CDR+)
Always
Below 1 ohms
W2-29 (R-) - K22-3 (CDR-)
W2-30 (L+) - K22-4 (CDL+)
W2-31 (L-) - K22-5 (CDL-)
W2-27 (SLD9) - K22-1 (CSLD)
W2-28 (R+) - Body ground
Always
10 Kohms or higher
W2-29 (R-) - Body ground
W2-30 (L+) - Body ground
W2-31 (L-) - Body ground
W2-27 (SLD9) - Body ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Fig. 265: Identifying W2 And K22 Connectors Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step.
2. CHECK TELEVISION DISPLAY
a. Reconnect the W2 display connector.
b. Using an oscilloscope, check the waveform between each terminal and the body ground according
to the conditions, as shown in the table below.
Waveform
TESTER CONNECTION SPECIFIED CONDITION
Tester Connection
Condition
Specified Condition
W2-28 (R+) - Body
ground
Audio sound is being
produced
A waveform synchronized with sound is
output
W2-29 (R-) - Body
ground
W2-30 (L+) - Body
ground
W2-31 (L-) - Body
ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Fig. 266: Identifying W2 Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE TELEVISION DISPLAY (see REMOVAL )
OK: PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS
TABLE (see PROBLEM SYMPTOMS TABLE )
SOUND SIGNAL CIRCUIT BETWEEN VIDEO TERMINAL AND TELEVISION DISPLAY
DESCRIPTION
This is the sound signal circuit from the video terminal to the television display.
WIRING DIAGRAM
Fig. 267: Sound Signal Circuit Between Video Terminal And Television Display - Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY - VIDEO TERMINAL)
a. Disconnect the W2 display connector.
b. Disconnect the T4 terminal connector.
c. Measure the resistance according to the value(s) in the table below.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Audio/Visual - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст