Toyota Tundra. Manual — part 718
Fig. 11: Power Window Regulator Master Switch Assembly LH Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a. Remove the motor (see REMOVAL ).
b. Apply battery voltage to connector terminals 1 and 2.
c. Check that the motor gear rotates smoothly as follows.
OK
MOTOR GEAR MEASUREMENT SPECIFIED CONDITION
Measurement Condition
Specified Condition
Battery positive (+) --> 1
Battery negative (-) --> 2
Motor gear rotates counterclockwise
Battery positive (+) --> 2
Battery negative (-) --> 1
Motor gear rotates clockwise
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Fig. 12: Identifying Rear Power Window Regulator Motor Assembly LH Connector
Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (see
REMOVAL )
OK: Go to Next Step
2. CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER SIDE MOTOR)
Fig. 13: Identifying Front View Of Wire Harness Connector Terminals (Master Switch And Driver
Side Motor)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
a. Disconnect the N2 master switch connector.
b. Disconnect the N3 motor connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
for Regular Cab:
MASTER SWITCH - DRIVER SIDE MOTOR (FOR REGULAR CAB)
for Double Cab:
MASTER SWITCH - DRIVER SIDE MOTOR (FOR DOUBLE CAB)
for CrewMax:
MASTER SWITCH - DRIVER SIDE MOTOR (FOR CREWMAX)
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to Next Step
3. CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
Tester Connection
Condition Specified Condition
N2-10 (U) - N3-2
Always
Below 1 ohms
N2-12 (D) - N3-1
N2-10 (U) or N3-2 - Body ground
Always
10 kohms or higher
N2-12 (D) or N3-1 - Body ground
Tester Connection
Condition Specified Condition
N2-3 (U) - N3-2
Always
Below 1 ohms
N2-4 (D) - N3-1
N2-3 (U) or N3-2 - Body ground
Always
10 kohms or higher
N2-4 (D) or N3-1 - Body ground
Tester Connection
Condition Specified Condition
N2-3 (U) - N3-2
Always
Below 1 ohms
N2-4 (D) - N3-1
N2-3 (U) or N3-2 - Body ground
Always
10 kohms or higher
N2-4 (D) or N3-1 - Body ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Fig. 14: Identifying Power Window Regulator Master Switch Assembly Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Remove the master switch (see REMOVAL ).
b. Reconnect the master switch connector.
c. Measure the voltage according to the value(s) in the table below.
Standard voltage
for Regular Cab:
POWER WINDOW REGULATOR MASTER SWITCH (FOR REGULAR CAB)
Tester
Connection
Condition
Specified Condition
N2-10 (U) -
N2-7 (E)
Ignition switch ON, driver side door power window
regulator switch OFF --> UP
Below 1 V --> 11 to
14 V
N2-12 (D) -
N2-7 (E)
Ignition switch ON, driver side door power window
regulator switch OFF --> DOWN
N2-12 (D) -
N2-7 (E)
Ignition switch ON, driver side door glass fully closed -->
power window AUTO DOWN operation --> driver side
Below 1 V --> 11 to
14 V --> Below 1 V
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Windshield/WindowGlass - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст