Toyota Tundra. Manual — part 573
A: Go to Next Step
2. CHECK SPEAKER
a. Check the malfunctioning speakers.
Result:
SPEAKER RESULT CHART
B: Go to step 5
C: Go to step 7
D: Go to step 9
A: Go to Next Step
3. INSPECT FRONT NO. 1 SPEAKER
a. Disconnect the M8 and N10 speaker connectors.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
FRONT NO. 1 SPEAKER TESTER CONNECTION SPECIFIED CONDITION
Fig. 408: Identifying M8 And N10 Speaker Connectors
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Result
Proceed to
Front No. 1 speaker
A
Front No. 2 speaker
B
Front No. 3 speaker
C
Front No. 4 speaker
D
Tester Connection Condition Specified Condition
1 - 2
Always
1.5 to 2.1 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
NG: REPLACE FRONT NO. 1 SPEAKER (See REMOVAL )
OK: Go to Next Step
4. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 1
SPEAKER)
a. Disconnect the M8 and N10 speaker connectors.
b. Disconnect the K17 amplifier connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance:
for LH
HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 1
SPEAKER) TESTER CONNECTION SPECIFIED CONDITION LH
for RH
HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 1
SPEAKER) TESTER CONNECTION SPECIFIED CONDITION RH
Tester Connection
Condition Specified Condition
K17-2 (WFL+) - N10-1
Always
Below 1 ohms
K17-1 (WFL-) - N10-2
K17-2 (WFL+) - Body ground
Always
10 kohms or higher
K17-1 (WFL-) - Body ground
Tester Connection
Condition Specified Condition
K17-9 (WFR+) - M8-1
Always
Below 1 ohms
K17-3 (WFR-) - M8-2
K17-9 (WFR+) - Body ground
Always
10 kohms or higher
K17-3 (WFR-) - Body ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Fig. 409: Identifying M8 And N10 Speaker Connectors And K17 Amplifier Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: REPLACE STEREO COMPONENT AMPLIFIER (See REMOVAL )
5. INSPECT FRONT NO. 2 SPEAKER
a. Disconnect the K10 and K12 speaker connectors.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance:
for LH
FRONT NO. 2 SPEAKER TESTER CONNECTION SPECIFIED CONDITION LH
Tester Connection Condition Specified Condition
1 (+) - 3 (TWL+)
Always
Below 1 ohms
2 (-) - 4 (TWL-)
3 (TWL+) - 4 (TWL-) Always
1.3 to 2.3 ohms
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Fig. 410: Identifying K10 And K12 Speaker Connectors
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Standard resistance:
for RH
FRONT NO. 2 SPEAKER TESTER CONNECTION SPECIFIED CONDITION RH
NG: REPLACE FRONT NO. 2 SPEAKER (See REMOVAL )
OK: Go to Next Step
6. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 2
SPEAKER)
a. Disconnect the K16 amplifier connector.
b. Disconnect the K10 and K12 speaker connectors.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance:
for LH
HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - FRONT NO. 2
SPEAKER) TESTER CONNECTION SPECIFIED CONDITION LH
Tester Connection Condition Specified Condition
1 (+) - 3 (TWR+)
Always
Below 1 ohms
2 (-) - 4 (TWR-)
3 (TWR+) - 4 (TWR-) Always
1.3 to 2.3 ohms
Tester Connection
Condition Specified Condition
K16-8 (FL+) - K12-3 (TWL+)
Always
Below 1 ohms
K16-7 (FL-) - K12-4 (TWL-)
K16-8 (FL+) - Body ground
Always
10 kohms or higher
K16-7 (FL-) - Body ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Navigation - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст