Toyota Tundra. Manual — part 1454
1. CHECK INJECTOR ASSEMBLY (POWER SOURCE)
a. Disconnect the fuel injector connector.
b. Turn the ignition switch to ON.
c. Measure the voltage according to the value(s) in the table below.
Standard voltage
STANDARD VOLTAGE SPECIFICATION
Fig. 297: Identifying Fuel Injector Connector
NG : Go to step 6
OK : Go to Next Step
2. INSPECT FUEL INJECTOR ASSEMBLY
a. Inspect the fuel injector. (See ON-VEHICLE INSPECTION ).
NG : REPLACE FUEL INJECTOR ASSEMBLY . (See FUEL INJECTOR ).
OK : Go to Next Step
Cylinder Tester Connection Switch Condition Specified Condition
No. 1
D11-1 - Ground
Ignition switch ON
11 to 14 V
No. 2
D26-1 - Ground
Ignition switch ON
11 to 14 V
No. 3
D13-1 - Ground
ignition switch ON
11 to 14 V
No. 4
D24-1 - Ground
Ignition switch ON
11 to 14 V
No. 5
D15-1 - Ground
Ignition switch ON
11 to 14 V
No. 6
D22-1 - Ground
Ignition switch ON
11 to 14 V
No. 7
D17-1 - Ground
Ignition switch ON
11 to 14 V
No. 8
D20-1 - Ground
Ignition switch ON
11 to 14 V
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (2UZ-FE) - Tundra
3. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
a. Disconnect the fuel injector connector.
b. Disconnect the ECM connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
STANDARD RESISTANCE SPECIFICATION
Cylinder
Tester Connection
Condition Specified Condition
No. 1
D11-2 - Body ground
Always
10 kohms or higher
D11-2 - D74-86 (#10)
Always
Below 1 ohms
No. 2
D26-2 - Body ground
Always
10 kohms or higher
D26-2 - D74-109 (#20) Always
Below 1 ohms
No. 3
D13-2 - Body ground
Always
10 kohms or higher
D13-2 - D74-85 (#30)
Always
Below 1 ohms
No. 4
D24-2 - Body ground
Always
10 kohms or higher
D24-2 - D74-108 (#40) Always
Below 1 ohms
No. 5
D15-2 - Body ground
Always
10 kohms or higher
D15-2 - D74-84 (#50)
Always
Below 1 ohms
No. 6
D22-2 - Body ground
Always
10 kohms or higher
D22-2 - D74-107 (#60) Always
Below 1 ohms
No. 7
D17-2 - Body ground
Always
10 kohms or higher
D17-2 - D74-83 (#70)
Always
Below 1 ohms
No. 8
D20-2 - Body ground
Always
10 kohms or higher
D20-2 - D74-106 (#80) Always
Below 1 ohms
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (2UZ-FE) - Tundra
Fig. 298: Identifying Fuel Injector Assembly & ECM Connectors
NG : REPAIR OR REPLACE HARNESS OR CONNECTOR
OK : Go to Next Step
4. REPLACE ECM
a. Replace the ECM (See REMOVAL ).
5. CHECK PROBLEM SYMPTOM DISAPPEARS
a. Check if the problem symptom disappears.
Result
RESULT REFERENCE
Result
Proceed To
Problem symptom disappears
A
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (2UZ-FE) - Tundra
B : GO TO PROBLEM SYMPTOMS TABLE
A : END
6. INSPECT FUSE (INJ)
a. Remove the INJ fuse from the engine room relay block.
b. Measure the resistance according to the value(s) in the table below.
Standard resistance
STANDARD RESISTANCE SPECIFICATION
Fig. 299: Identifying INJ Fuse
NG : CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO
FUSE AND REPLACE FUSE
OK : Go to Next Step
7. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - INTEGRATION
RELAY)
a. Disconnect the fuel injector connector.
b. Remove the integration relay from the engine room relay block.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
Problem symptom does not disappear
B
Tester Connection Condition Specified Condition
INJ fuse
Always
Below 1 ohms
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (2UZ-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст