Toyota Tundra. Manual — part 2801
Fig. 22: Identifying D35 Park/Neutral Position Switch Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (See REMOVAL )
OK: Go to next step.
2. INSPECT TRANSMISSION CONTROL SWITCH
a. for Column Shift Type:
1. Disconnect the J25 transmission control switch connector.
2. Measure the resistance according to the value (s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION TABLE
2 (RB) - 6 (PL)
4 (B) - 5 (L)
Shift lever position not on P
10 kohms or higher
2 (RB) - 1 (RL)
Shift lever position not on R
10 kohms or higher
2 (RB) - 9 (NL)
4 (B) - 5 (L)
Shift lever position not on N
10 kohms or higher
2 (RB) - 7 (DL)
Shift lever position not on D
Shift lever position not on S, "+" or "-"
10 kohms or higher
Tester Connection
Condition
Specified Condition
6 (IG) - 13 (S)
Shift lever position on S, "+" or "-"
Below 1 ohms
6 (IG) - 13 (S)
Shift lever position not on S, "+" or "-" 10 kohms or higher
2009 Toyota Tundra
2009 TRANSMISSION AB60F Automatic Transaxle - Tundra
Fig. 23: Identifying J25 Transmission Control Switch Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. for Floor Shift Type:
1. Disconnect the J24 transmission control switch connector.
2. Measure the resistance according to the value (s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION TABLE
Result
RESULT REFERENCE
Tester Connection
Condition
Specified Condition
3 (IG) - 7 (S)
Shift lever position on S, "+" or "-"
Below 1 ohms
3 (IG) - 7 (S)
Shift lever position not on S, "+" or "-" 10 kohms or higher
Result
Proceed to
OK
A
NG (for Column Shift Type)
B
NG (for Floor Shift Type)
C
2009 Toyota Tundra
2009 TRANSMISSION AB60F Automatic Transaxle - Tundra
Fig. 24: Identifying J24 Transmission Control Switch Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
B: REPLACE COLUMN SHIFT LEVER SUB-ASSEMBLY (TRANSMISSION CONTROL
SWITCH) (See REMOVAL )
C: REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL
SWITCH) (See ON-VEHICLE INSPECTION )
A: Go to next step.
3. CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)
a. Disconnect the D35 park/neutral position switch connector.
b. Measure the voltage according to the value (s) in the table below.
Standard voltage
TESTER CONNECTION SPECIFIED CONDITION TABLE
Tester Connection
Switch Condition
Specified
Condition
D35-2 (RB) - Body
ground
Ignition switch ON
11 to 14 V
D35-2 (RB) - Body
ground
Ignition switch off
Below 1 V
2009 Toyota Tundra
2009 TRANSMISSION AB60F Automatic Transaxle - Tundra
Fig. 25: Identifying D35 Park/Neutral Position Switch Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION
SWITCH - IGNITION SWITCH)
OK: Go to next step.
4. CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)
a. for Column Shift Type:
1. Disconnect the J25 transmission control switch connector.
2. Measure the voltage according to the value (s) in the table below.
Standard voltage
TESTER CONNECTION SPECIFIED CONDITION TABLE
Tester Connection
Switch Condition
Specified
Condition
J25-6 (IG) - Body
ground
Ignition switch ON
11 to 14 V
J25-6 (IG) - Body
ground
Ignition switch off
Below 1 V
2009 Toyota Tundra
2009 TRANSMISSION AB60F Automatic Transaxle - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст