Toyota Tundra. Manual — part 1899
d
Disconnect the 4 connectors from the connector holder block
Fig. 355: Locating Connector Holder Block
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
e
Remove the bolt and connector bracket and disconnect the air pump connector
f
Remove the bolt and disconnect the ground wire
g
Disconnect the air injection system hose
Fig. 356: Locating Connector Bracket Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
h
Remove the nut and disconnect the wire from the positive (+) battery terminal
i
Disconnect the positive (+) battery terminal
j
Remove the bolt and disconnect the ground wire
k
Disconnect the 4 air injection control driver connectors
l
Remove the nut and disconnect the wire from the engine room junction block
m
Disconnect the 3 connectors from the engine room junction block
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (2UZ-FE) - Tundra
Fig. 357: Locating Air Injection Control Driver Connectors
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
23
DISCONNECT COOLER COMPRESSOR ASSEMBLY (See REMOVAL )
24
DISCONNECT VANE PUMP ASSEMBLY (See REMOVAL )
25
REMOVE GENERATOR ASSEMBLY (See REMOVAL )
26
REMOVE NO. 1 WATER BY-PASS PIPE
a
Remove the 2 bolts and water by-pass pipe
27
REMOVE EXHAUST PIPE ASSEMBLY
a
for Regular cab standard deck, refer to the following procedures (see REMOVAL )
b
except Regular cab standard deck, refer to the following procedures (see REMOVAL )
Fig. 358: Locating Exhaust Pipe Assembly
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (2UZ-FE) - Tundra
28
REMOVE PROPELLER SHAFT ASSEMBLY
a
for 2 Joint type, refer to the following procedures (see )
b
for 3 Joint type, refer to the following procedures (see )
29
REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
a
for 2WD, refer to the following procedures (see REMOVAL )
b
for 4WD, refer to the following procedures (see REMOVAL )
30
REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
a
Using SST, hold the crankshaft
SST 09213-70011 (09213-70020), 09330-00021
Fig. 359: Holding Crankshaft Using SST
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Remove the 8 bolts, front drive plate spacer, drive plate and rear drive plate spacer
Fig. 360: Locating Drive Plate Spacer Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
31
REMOVE ENGINE ASSEMBLY
a
Attach an engine sling device and hang the engine with a chain block
b
Remove the 4 engine mounting insulator's bolts
c
Lift the engine out from the vehicle slowly and carefully
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (2UZ-FE) - Tundra
Fig. 361: Locating Engine Assembly Insulator Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
32
REMOVE NO. 3 AIR TUBE (See REMOVAL )
33
REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (See REMOVAL )
34
REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH (See REMOVAL )
35
REMOVE NO. 2 AIR TUBE (See REMOVAL )
36
REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE (See REMOVAL )
37
REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (See REMOVAL )
38
REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH (See REMOVAL )
39
INSTALL ENGINE ON ENGINE STAND
a
Install the engine onto an engine stand with the bolts
INSTALLATION
1
REMOVE ENGINE STAND
a
Attach an engine sling device and hang the engine with a chain block
b
Remove the bolts and engine assembly from the engine stand
2
INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH (See INSTALLATION )
3
INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (See INSTALLATION )
4
INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE (See INSTALLATION )
NOTE:
Make sure the engine is clear of all wiring, hoses and cables.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (2UZ-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст