Toyota Tundra. Manual — part 2304
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
19
INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE (See INSTALLATION )
20
INSTALL OIL FILTER BRACKET (w/o Oil Cooler)
a
Apply a light coat of engine oil to 2 new O-rings
Fig. 122: Locating O-Rings
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Install the 2 O-rings to the timing chain cover
c
Install the oil filter bracket with the 2 bolts and 2 nuts
Torque: 35 N*m (357 kgf*cm, 26 ft.*lbf)
Fig. 123: Locating Oil Filter Bracket Bolts And Nuts (W/O Oil Cooler)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
21
INSTALL OIL FILTER BRACKET (w/ Oil Cooler) (See INSTALLATION )
22
INSTALL NO. 1 OIL COOLER BRACKET (w/ Oil Cooler) (See INSTALLATION )
23
INSTALL NO. 2 WATER BY-PASS PIPE (w/ Oil Cooler)
a
Connect the 4 hoses
b
Install the water by-pass hose with the 3 bolts
Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FBE) - Tundra
Fig. 124: Locating No. 2 Water By-Pass Hoses And Bolts (W/ Oil Cooler)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
24
INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY (See REMOVAL )
25
INSTALL OIL FILTER ELEMENT (See REPLACEMENT )
26
CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY
a
Connect the fuel tube with the 2 bolts
Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FBE) - Tundra
Fig. 125: Locating No. 2 Fuel Tube Sub-Assembly Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
27
CONNECT COOLER COMPRESSOR ASSEMBLY
a
Install the cooler compressor with the 2 stud bolts
Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
Fig. 126: Cooler Compressor Bolts And Nuts Tightening Order
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Install the 2 bolts and 2 nuts
NOTE:
Tighten the bolts and nuts in the order shown in the illustration to
install the cooler compressor.
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FBE) - Tundra
Torque: 25 N*m (250 kgf*cm, 18 ft.*lbf)
28
CONNECT HEATER HOSE AND PIPE
a
Connect the 3 hoses
b
Install the 2 bolts
Torque: 18 N*m (184 kgf*cm, 13 ft.*lbf)
Fig. 127: Locating Heater Hoses And Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
29
CONNECT AIR PUMP HOSE AND WIRE HARNESS
a
Connect the No 2 and No 3 air hoses
Fig. 128: Locating Clamps With No. 2 And No. 3 Air Pump Hoses
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
Connect the 2 clamps and air pump wire harness
30
INSTALL INTAKE MANIFOLD
a
Install the intake manifold (See INSTALLATION )
31
CONNECT ENGINE WIRE
a
Engine Room RH Side:
1
Connect the 5 clamps
2
Connect the throttle position sensor and throttle control motor connector
3
Connect the 2 air pump connectors
2009 Toyota Tundra
2009 ENGINE Lubrication (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст