Toyota Tundra. Manual — part 1887
Fig. 286: Using Vernier Caliper To Measure Tension Portion Of Connecting Rod Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
9
INSPECT CRANKSHAFT BEARING CAP BOLT
a
Using a vernier caliper, measure the tension portion diameter of the main bearing cap bolt
Measuring point: 67.0 mm (2.64 in.)
Standard diameter: 10.760 to 10.970 mm (0.424 to 0.432 in.)
Minimum diameter: 10.40 mm (0.409 in.)
If the diameter is less than the minimum, replace the cap bolt
Fig. 287: Using Vernier Caliper To Measure Tension Portion Diameter Of Main Bearing Cap
Bolt
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
10
INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY
a
Push the check valve with a pin to check if it is stuck If stuck, replace the oil nozzle
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (2UZ-FE) - Tundra
Fig. 288: Identifying No. 1 Oil Nozzle Sub-Assembly
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b
While covering A, apply air into B Then check the oil nozzle for damage or clogging Perform the
check again while covering B and applying air into A
If there is an air leak, repair or replace the oil nozzle If the oil nozzle is clogged, clean or replace it
Fig. 289: Checking Oil Nozzle For Damage Or Clogging
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c
Push the check valve while covering A, and apply air into B Check that air passes through the oil
nozzle Perform the check again while covering B, pushing the check valve and applying air into A
If air cannot pass through, clean or replace the oil nozzle
Fig. 290: Checking Air Passes Through Oil Nozzle
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
REPLACEMENT
1
REPLACE RING PIN
a
Remove the ring pin
b
Using a plastic-faced hammer, tap in new ring pins until they stop
NOTE:
It is not necessary to remove the ring pin unless it is being replaced.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (2UZ-FE) - Tundra
Fig. 291: Identifying Ring Pin Dimension
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2
REPLACE STRAIGHT PIN
a
Remove the straight pin
b
Using a plastic-faced hammer, tap in new straight pins until they stop
Fig. 292: Identifying Straight Pins Dimension
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3
REPLACE CYLINDER BLOCK TIGHT PLUG
NOTE:
It is not necessary to remove the straight pin unless it is being replaced.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (2UZ-FE) - Tundra
a
Remove the tight plugs
b
Apply adhesive to the holes' inner circumference where the tight plugs contact
Adhesive: Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Fig. 293: Applying Adhesive To Holes' Inner Circumference
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c
Using SST and a hammer, tap in new tight plugs as shown below
SST 09950-60010 (09951-00340), 09950-70010 (09951-07100)
NOTE:
If water leaks from the tight plug or the plug corrodes, replace it.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (2UZ-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст