Toyota Tundra. Manual — part 2193
Fig. 62: Identifying Air Cleaner Element
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
c. Remove the 2 bolts and air cleaner case.
Fig. 63: Identifying Air Cleaner Case Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSTALLATION
1. INSTALL AIR CLEANER ASSEMBLY
a. Install the air cleaner case with the 2 bolts.
Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)
Fig. 64: Identifying Air Cleaner Case Bolts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Intake (2UZ-FE) - Tundra
b. Install the air cleaner element onto the air cleaner case.
c. Install the air cleaner cap.
1. Fasten the 4 hook clamps.
2. Connect the MAF meter connector.
3. Attach the wire harness clamp.
Fig. 65: Identifying Air Cleaner Element
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. INSTALL NO. 2 VENTILATION HOSE
a. Install the No. 2 ventilation hose and vacuum hose.
Fig. 66: Identifying No. 2 Ventilation Hose
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3. INSTALL AIR CLEANER HOSE ASSEMBLY
a. Install the air cleaner hose.
Torque: 4.0 N*m (41 kgf*cm, 35 in.*lbf)
HINT:
Make sure that the clamp band end is aligned with the limit mark when the hose clamp is tightened,
as indicated by A and B in the illustration.
2009 Toyota Tundra
2009 ENGINE Intake (2UZ-FE) - Tundra
Fig. 67: Identifying Air Cleaner Hose Clamp
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Connect the vacuum hose.
c. Connect the No. 2 ventilation hose.
4. INSTALL THROTTLE BODY COVER SUB-ASSEMBLY
a. Install the throttle body cover with the 2 cap nuts.
Torque: 7.5 N*m (76 kgf*cm, 66 in.*lbf)
Fig. 68: Locating Throttle Body Cover With Cap Nuts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE Intake (2UZ-FE) - Tundra
2009 ENGINE
Engine Mechanical (3UR-FBE) - Tundra
ENGINE
ON-VEHICLE INSPECTION
1. INSPECT IGNITION TIMING
a. Warm up and stop the engine.
1. Allow the engine to warm up to a normal operating temperature.
b. When using the Techstream:
1. Connect the Techstream to the DLC3.
2. Start the engine and idle it.
3. Turn the Techstream main switch ON.
4. Enter the following menus: Powertrain/Engine and ECT/Data List/Primary/IGN Advance.
HINT:
Refer to the Techstream operator's manual for further details.
Standard ignition timing:
8 to 12° BTDC @ idle (transmission in neutral and A/C switch OFF)
5. Disconnect the Techstream from the DLC3.
c. When not using the Techstream:
1. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No.
1 cylinder.
Fig. 1: Connecting Tester Probe Of Timing Light To Wire Of Ignition Coil Connector
For No. 1 Cylinder
NOTE:
Use a timing light that detects primary signals.
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
2009 Toyota Tundra
2009 ENGINE Engine Mechanical (3UR-FBE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст