Toyota Tundra. Manual — part 2711
Fig. 15: Identifying Tilt & Telescopic Manual Switch Circuit Malfunction Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. READ VALUE USING TECHSTREAM (TILT AND TELESCOPIC MANUAL SWITCH)
a. Use the Data List to check if the tilt and telescopic manual switch is functioning properly.
Fig. 16: Identifying Tilt & Telescopic Manual Switch
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Tilt & Telescopic
TILT AND TELESCOPIC - DATA LIST TABLE
Tester
Display
Measurement Item/Range
Normal Condition
Diagnostic
Note
Neutral position: Below
2009 Toyota Tundra
2009 STEERING Steering Column - Tundra
Result
RESULT REFERENCE TABLE
B: REPLACE HEADLIGHT DIMMER SWITCH (See HEADLIGHT DIMMER SWITCH )
C: REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (See MULTIPLEX TILT AND
TELESCOPIC ECU (for Power Tilt and Power Telescopic Steering Column) )
A: Go to next step.
2. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU -
HEADLIGHT DIMMER SWITCH)
a. Disconnect the J47 multiplex tilt and telescopic ECU connector.
b. Disconnect the J10 headlight dimmer switch connector.
c. Measure the resistance according to the value (s) in the table below.
Standard Resistance
STANDARD RESISTANCE SPECIFICATION TABLE
T&T Manual
SW
Voltage data of manual switch/min.: 0
V, max.: 5 V
0.2 V
Tilt up: 1.67 to 2.13 V
Tilt down: 0.54 to 0.74 V
Telescopic contract: 1.08
to 1.40 V
Telescopic extend: 2.22 to
2.77 V
-
Result
Proceed to
Switch voltages in all directions are outside the standard.
A
Switch voltages in certain directions are outside the standard.
B
Switch voltages in all directions are within the standard.
C
Tester Connection
Condition Specified Condition
J47-4 (VC) - J10-8 (VC)
Always
Below 1 ohms
J47-3 (MSW) - J10-10 (MSW) Always
Below 1 ohms
J10-8 (VC) - Body ground
Always
10 kohms or higher
J10-10 (MSW) - Body ground
Always
10 kohms or higher
2009 Toyota Tundra
2009 STEERING Steering Column - Tundra
Fig. 17: Identifying Multiplex Tilt & Telescopic ECU & Headlight Dimmer Switch Connector
Terminal
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step.
3. CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE)
a. Reconnect the J47 multiplex tilt and telescopic ECU connector.
b. Measure the voltage according to the value (s) in the table below.
Standard Voltage
STANDARD VOLTAGE SPECIFICATION TABLE
Fig. 18: Identifying J47 Multiplex Tilt & Telescopic ECU Connector
Tester Connection
Switch Condition Specified Condition
J47-4 (VC) - J47-3 (MSW) Ignition switch ON
4.9 to 5.1 V
2009 Toyota Tundra
2009 STEERING Steering Column - Tundra
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (See MULTIPLEX TILT AND
TELESCOPIC ECU (for Power Tilt and Power Telescopic Steering Column) )
OK: Go to next step.
4. INSPECT HEADLIGHT DIMMER SWITCH (TILT AND TELESCOPIC MANUAL SWITCH)
a. Disconnect the J10 headlight dimmer switch connector.
b. Measure the resistance according to the value (s) in the table below.
Standard Resistance
STANDARD RESISTANCE SPECIFICATION TABLE
Fig. 19: Identifying J10 Headlight Dimmer Switch Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE HEADLIGHT DIMMER SWITCH (See HEADLIGHT DIMMER SWITCH )
OK: REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (See MULTIPLEX TILT AND
TELESCOPIC ECU (for Power Tilt and Power Telescopic Steering Column) )
DTC B2610: TILT POSITION SENSOR OR TILT MOTOR CIRCUIT MALFUNCTION
DESCRIPTION
Tester Connection Switch Condition Specified Condition
8 (VC) - 10 (MSW)
Tilt up
342 to 378 ohms
Tilt down
1890.5 to 2089.5 ohms
Telescopic contract 750.5 to 829.5 ohms
Telescopic extend
152 to 168 ohms
2009 Toyota Tundra
2009 STEERING Steering Column - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст