Toyota Tundra. Manual — part 825
2. REMOVE FRONT END PANEL LH
a. Using a clip remover, remove the 2 clips.
Fig. 5: Identifying Front End Panel LH Clips And Pins
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Detach the 2 pins and remove the panel.
3. REMOVE FRONT END PANEL RH
HINT:
Use the same procedures described for the LH side.
4. REMOVE FRONT BUMPER COVER
a. Using a screwdriver, remove the 2 pin hold clips.
HINT:
Use the same procedures for the RH side and LH side.
b. Using a clip remover, remove the 2 clips.
HINT:
Use the same procedures for the RH side and LH side.
c. Put protective tape around the bumper cover.
d. Using a clip remover, remove the 8 clips.
(see INITIALIZATION ).
After the ignition switch is turned OFF, the navigation system
requires approximately 90 seconds to record various types of
memory and settings. As a result, after turning the ignition switch
OFF, wait 90 seconds or more before disconnecting the cable from
the negative (-) battery terminal.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Exterior - Tundra
Fig. 6: Identifying Clips And Screws
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
e. Remove the 9 screws.
f. Detach the 4 claws and remove the bumper cover.
Fig. 7: Identifying Bumper Cover Claws
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
g. w/ Fog Light:
Disconnect the fog light connectors and remove the bumper cover.
h. w/ Intuitive Parking Assist System:
Disconnect the ultrasonic sensor connectors and remove the bumper cover.
5. REMOVE FRONT BUMPER SIDE SUPPORT LH
a. Remove the 2 screws.
b. Detach the 3 clips and remove the side support.
6. REMOVE FRONT BUMPER SIDE SUPPORT RH
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Exterior - Tundra
Fig. 8: Identifying Front Bumper Side Support RH Screws
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
HINT:
Use the same procedures described for the LH side.
7. REMOVE FRONT UPPER CENTER BUMPER RETAINER
a. Remove the 6 nuts and retainer.
Fig. 9: Identifying Front Upper Center Bumper Retainer And Nuts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
8. REMOVE FRONT BUMPER END RETAINER LH
a. Remove the 3 nuts and retainer.
9. REMOVE FRONT BUMPER END RETAINER RH
HINT:
Use the same procedures described for the LH side.
10. REMOVE FRONT BUMPER REINFORCEMENT
a. Remove the 6 nuts and reinforcement.
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Exterior - Tundra
Fig. 10: Identifying Front Bumper Reinforcement Nuts And Retainer
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Fig. 11: Identifying Front Bumper Reinforcement Nuts
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
11. REMOVE FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY LH
a. Remove the 4 nuts and bumper extension.
Fig. 12: Identifying Nuts And Bumper Extension
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
12. REMOVE FRONT NO. 2 BUMPER EXTENSION SUB-ASSEMBLY RH
HINT:
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Exterior - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст