Toyota Tundra. Manual — part 1274
Fig. 276: Checking Harness & Connector (Power Source)
OK : Go to next step.
6. INSPECT STARTER
a. Inspect the starter for 1.6 kW type. (See INSPECTION ).
b. Inspect the starter for 2.0 kW type. (See INSPECTION ).
Result
RESULT CHART
B : REPLACE STARTER . (See STARTER (FOR 1.6 KW TYPE) ).
C : REPLACE STARTER (See STARTER (FOR 2.0 KW TYPE) ).
A : REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER - STARTER RELAY
(ST), BATTERY)
7. CHECK IGNITION SWITCH (POWER SOURCE)
a. Disconnect the J9 ignition switch connector.
b. Measure the voltage according to the value (s) in the table below.
Test Result
Proceed To
OK
A
NG (for 1.6 kW type)
B
NG (for 2.0 kW type)
C
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (1GR-FE) - Tundra
Standard voltage
TESTER CONNECTION SPECIFIED CONDITION
NG : REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY
POSITIVE TERMINAL)
Fig. 277: Identifying J9 Ignition Switch Connector Terminals
OK : Go to next step.
8. INSPECT IGNITION SWITCH
a. Inspect the ignition switch. (See INSPECTION ).
NG : REPLACE IGNITION SWITCH . (See IGNITION SWITCH ).
OK : Go to next step.
9. CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a. Disconnect the D35 PNP switch connector.
b. Measure the voltage according to the value (s) in the table below.
Standard voltage
TESTER CONNECTION SPECIFIED CONDITION
Tester Connection
Condition Specified Condition
J9-5 (AM2) - Body ground Always
11 to 14 V
Tester Connection
Condition
Specified Condition
D35-4 - Body ground While cranking the engine
11 to 14 V
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (1GR-FE) - Tundra
NG : REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - IGNITION
SWITCH)
Fig. 278: Identifying D35 PNP Switch Connector Terminals
OK : Go to next step.
10. INSPECT PARK/NEUTRAL POSITION SWITCH
a. Disconnect the D35 PNP switch connector.
b. Measure the resistance according to the value (s) in the table below.
Standard resistance
TESTER CONNECTION SPECIFIED CONDITION
Result
RESULT CHART
B : REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (See REMOVAL )
Tester Connection
Condition
Specified Condition
4 - 5
Shift lever position P
Below 1 ohms
4 - 5
Shift lever position N
Below 1 ohms
Test Result Proceed To
OK
A
NG
B
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (1GR-FE) - Tundra
Fig. 279: Identifying D35 PNP Switch Connector Terminals
A : REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - ECM)
11. CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ECM)
a. Disconnect the J9 ignition switch connector.
b. Disconnect the A24 ECM connector.
c. Measure the resistance according to the value (s) in the table below.
Standard resistance (Check for open)
TESTER CONNECTION SPECIFIED CONDITION
Standard resistance (Check for short)
TESTER CONNECTION SPECIFIED CONDITION
NG : REPAIR OR REPLACE HARNESS OR CONNECTOR
Tester Connection
Condition Specified Condition
J9-7 (ST2) - A24-14 (STSW) Always
Below 1 ohms
Tester Connection
Condition Specified Condition
J9-7 (ST2) or A24-14 (STSW) - Body ground Always
10 kohms or higher
2008 Toyota Tundra
2008 ENGINE PERFORMANCE Engine Control System (1GR-FE) - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст