Toyota Tundra. Manual — part 1660
3. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (except Regular Cab Standard Deck) (See
REMOVAL )
4. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY (for Regular Cab Standard Deck) (See
REMOVAL )
5. REMOVE FRONT EXHAUST PIPE ASSEMBLY (See REMOVAL )
6. REMOVE HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)
a. Using SST, remove the sensor.
SST 09224-00010
Fig. 413: Identifying SST 09224-00010
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
7. REMOVE HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)
a. Using SST, remove the sensor.
SST 09224-00010
Fig. 414: Identifying SST 09224-00010
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2009 Toyota Tundra
2009 ENGINE PERFORMANCE Engine Control System (3UR-FBE) - Tundra
Saturday, June 19, 2010 7:34:51 PM
Page 733
© 2006 Mitchell Repair Information Company, LLC.
INSTALLATION
1. INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)
a. Install the sensor to the exhaust pipe by hand.
Fig. 415: Installing Heated Oxygen Sensor To Exhaust Pipe (Bank 2 Sensor 2)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Using SST, tighten the sensor.
SST 09224-00010
Torque: without SST
44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST
40 N*m (408 kgf*cm, 30 ft.*lbf)
HINT:
Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with
a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench
and SST based on the "without SST" torque specification (See PRECAUTION ).
Make sure SST and the wrench are connected in a straight line.
2009 Toyota Tundra
2009 ENGINE PERFORMANCE Engine Control System (3UR-FBE) - Tundra
Saturday, June 19, 2010 7:34:51 PM
Page 734
© 2006 Mitchell Repair Information Company, LLC.
Fig. 416: Identifying SST Fulcrum Length
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
2. INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)
a. Install the sensor to the exhaust pipe by hand.
Fig. 417: Installing Heated Oxygen Sensor To Exhaust Pipe (Bank 1 Sensor 2)
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
b. Using SST, tighten the sensor.
SST 09224-00010
Torque: without SST
44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST
40 N*m (408 kgf*cm, 30 ft.*lbf)
HINT:
Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with
a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench
and SST based on the "without SST" torque specification (See PRECAUTION ).
Make sure SST and the wrench are connected in a straight line.
2009 Toyota Tundra
2009 ENGINE PERFORMANCE Engine Control System (3UR-FBE) - Tundra
Saturday, June 19, 2010 7:34:51 PM
Page 735
© 2006 Mitchell Repair Information Company, LLC.
Fig. 418: Identifying SST Fulcrum Length
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
3. INSTALL FRONT EXHAUST PIPE ASSEMBLY (See INSTALLATION )
4. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY (for Regular Cab Standard Deck) (See
INSTALLATION )
5. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY (except Regular Cab Standard Deck) (See
INSTALLATION )
6. INSTALL FRONT PROPELLER SHAFT ASSEMBLY (See INSTALLATION )
7. INSTALL PROPELLER SHAFT HEAT INSULATOR (See INSTALLATION )
8. INSPECT FOR EXHAUST GAS LEAK (See INSTALLATION )
IGNITION RELAY NO. 2
ON-VEHICLE INSPECTION
1. REMOVE INTEGRATION RELAY (UNIT E)
a. Remove the engine room relay block cover.
b. Using a screwdriver, detach the 2 claws and remove the integration relay from the engine room
relay block.
HINT:
Tape the screwdriver tip before use.
c. Disconnect the 3 connectors.
2009 Toyota Tundra
2009 ENGINE PERFORMANCE Engine Control System (3UR-FBE) - Tundra
Saturday, June 19, 2010 7:34:51 PM
Page 736
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст