Toyota Tundra. Manual — part 343
NG: REPLACE TRANSMITTER BATTERY (see REPLACEMENT )
OK: REPLACE DOOR CONTROL TRANSMITTER
5. CHECK ELECTRICAL NOISE
a. Move the transmitter near the vicinity of the door control receiver.
HINT:
For Regular Cab, refer to the PARTS LOCATION for the location of the door control
receiver (see DOOR CONTROL RECEIVER (FOR REGULAR CAB) ).
For Double Cab, refer to the PARTS LOCATION for the location of the door control
receiver (see DOOR CONTROL RECEIVER (FOR DOUBLE CAB) ).
For CrewMax, refer to the PARTS LOCATION for the location of the door control receiver
(see DOOR CONTROL RECEIVER (FOR CREWMAX) ).
b. Press and hold either the LOCK or UNLOCK transmitter switch for 1 second, and check that the
doors are locked or unlocked accordingly.
OK: Wireless door control functions operate normally
HINT:
Check if electrical noise is the cause by moving the door control transmitter closer to the
door control receiver. Moving closer will decrease the effects of electrical noise.
If the operation check can be performed normally, there is a high probability that electrical
noise or a decrease in outputs from the door control transmitter was the cause. There is a high
probability that electrical noise was the cause if the problem occurs only in a certain location
or only during a certain time of day. Also, custom components may be causing electrical
noise. If custom components are installed in the vehicle, remove them and perform the
operation check again.
NG: Go to step 6
OK: FIND CAUSE OF ELECTRICAL NOISE AND REMOVE IT
6. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL RECEIVER)
a. Disconnect the J3 ECU connector.
b. Disconnect the Q7 receiver connector.
c. Measure the resistance according to the value(s) in the table below.
Standard resistance
HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL RECEIVER)
STANDARD RESISTANCE SPECIFICATION
Tester Connection
Condition Specified Condition
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Door Lock - Tundra
Fig. 62: Identifying J3 ECU And Q7 Receiver Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step
7. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND
BODY GROUND)
a. Disconnect the Q7 receiver connector.
b. Measure the resistance and voltage according to the value(s) in the table below.
J3-12 (RDA) - Q7-2 (RDA)
Always
Below 1 ohms
J3-10 (PRG) - Q7-3 (PRG)
J3-12 (RDA) - Q7-2 (RDA) - Body ground
Always
10 kohms or higher
J3-10 (PRG) - Q7-3 (PRG) - Body ground
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Door Lock - Tundra
Fig. 63: Identifying Q7 Receiver Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Standard voltage
HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY
GROUND) STANDARD VOLTAGE SPECIFICATION
Standard resistance
HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY
GROUND) STANDARD RESISTANCE SPECIFICATION
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: Go to next step
8. CHECK DOOR CONTROL RECEIVER (OUTPUT)
a. Measure the voltage according to the value(s) in the table below.
Standard voltage
DOOR CONTROL RECEIVER (OUTPUT) STANDARD VOLTAGE SPECIFICATION
Tester Connection
Condition Specified Condition
Q7-5 (+B) - Body Ground Always
11 to 14 V
Tester Connection
Condition Specified Condition
Q7-1 (GND) - Body ground Always
Below 1 ohms
Tester
Connection
Tool Setting
Switch Condition
Specified
Condition
Q7-2 (RDA) -
Body ground
10V/DIV., 50
µsec./DIV.
Transmitter switch ON --> OFF (No key in
ignition key cylinder, all doors closed)
Pulse
generation
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Door Lock - Tundra
Fig. 64: Identifying Door Control Receiver Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
OK: Door control receiver outputs pulse generation.
Result
DOOR CONTROL RECEIVER (OUTPUT) RESULT REFERENCE
B: REPLACE DOOR CONTROL RECEIVER (see REMOVAL (FOR REGULAR CAB) )
C: REPLACE DOOR CONTROL RECEIVER (see REMOVAL (FOR DOUBLE CAB) )
D: REPLACE DOOR CONTROL RECEIVER (see DOOR CONTROL RECEIVER (FOR
CREWMAX) )
Result
Proceed to
OK
A
NG (for Regular Cab)
B
NG (for Double Cab)
C
NG (for CrewMax)
D
2009 Toyota Tundra
2009 ACCESSORIES AND EQUIPMENT Door Lock - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст