Toyota Tundra. Manual — part 2524
TERMINALS OF ECU
1. CHECK COMBINATION METER (METER ECU)
Fig. 4: Identifying Combination Meter (Meter ECU) Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Measure the resistance and voltage according to the value(s) in the table below.
COMBINATION METER (METER ECU) CONNECTOR TERMINALS RESISTANCE
CHART
Wire harness
FRONT PASSENGER SIDE
SEAT BELT WARNING
LIGHT MALFUNCTION
Integration control and panel
FRONT PASSENGER SIDE
SEAT BELT WARNING
LIGHT MALFUNCTION
Front seat inner belt RH
FRONT PASSENGER SIDE
SEAT BELT WARNING
LIGHT MALFUNCTION
Terminal No.
(Symbols)
Wiring
Color
Terminal Description
Condition
Specified Condition
J28-18 (B) -
Body ground
LG -
Body
ground
Power source
Always
11 to 14 V
J28-15 (P/SB) -
Body ground
L - Body
ground
Front passenger side
seat belt warning light
signal
Front passenger side
seat is occupied, seat
belt is fastened
Below 1 V
Front passenger side
seat is occupied, seat
belt is unfastened
Alternating between
11 to 14 V and below
1 V
J28-31 (TX+) -
Body ground
Y - Body
ground
Accessory meter input
signal
Ignition switch ON
Local communication
signal
2009 Toyota Tundra
2009 RESTRAINTS Seat Belt - Tundra
If the result is not as specified, the ECU may have a malfunction.
2. CHECK INTEGRATION CONTROL AND PANEL
Fig. 5: Identifying Integration Control And Panel Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Measure the voltage according to the value(s) in the table below.
INTEGRATION CONTROL AND PANEL CONNECTOR TERMINALS VOLTAGE CHART
If the result is not as specified, the panel may have a malfunction.
3. CENTER AIRBAG SENSOR
J28-33 (CANH)
- J28-34
(CANL)
SB - W
Driver side seat belt
warning light signal
(CAN signal)
Ignition switch OFF
108 to 132 ohms
J28-33 (CANH)
- J28-40 (E1)
SB - W-B
Driver side seat belt
warning light signal
(CAN signal)
Ignition switch OFF
200 ohms or higher
J28-34 (CANL)
- J28-40 (E1)
W - W-B
Driver side seat belt
warning light signal
(CAN signal)
Ignition switch OFF
200 ohms or higher
J28-40 (E1) -
Body ground
W-B -
Body
ground
Ground
Always
Below 1 ohms
Terminal No.
(Symbols)
Wiring
Color
Terminal Description
Condition
Specified Condition
J37-16 (IG+) -
Body ground
SB - Body
ground
Power source
Always
11 to 14 V
J37-14 (PBEW)
- Body ground
SB - Body
ground
Front passenger side
seat belt warning light
signal
Front passenger side seat
is occupied, seat belt is
fastened
Below 1 V
Front passenger side seat
is occupied, seat belt is
unfastened
Alternating between
11 to 14 V and below
1 V
2009 Toyota Tundra
2009 RESTRAINTS Seat Belt - Tundra
Fig. 6: Identifying Airbag Sensor Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
AIRBAG SENSOR CONNECTOR TERMINALS REFERENCE CHART
4. CHECK OCCUPANT CLASSIFICATION ECU
Fig. 7: Identifying Occupant Classification ECU Connector Terminals
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
a. Measure the voltage and resistance according to the value(s) in the table below.
OCCUPANT CLASSIFICATION ECU TERMINALS VOLTAGE CHART
Terminal No. Terminal Symbol
Destination
J46-13
FSR+
Occupant classification ECU
J46-22
FSR-
Occupant classification ECU
P1-11
LBE+
Front seat inner belt LH (Seat belt buckle switch LH)
P1-12
LBE+
Front seat inner belt LH (Seat belt buckle switch LH)
Terminal No.
(Symbols)
Wiring Color
Terminal Description
Condition
Specified
Condition
Y2-1 (+B) - Body
ground
G - Body
ground
Power source
Always
11 to 14 V
Y2-7 (IG) - Body
ground
SB - Body
ground
Occupant classification
ECU +B line
Ignition switch
ON
11 to 14 V
2009 Toyota Tundra
2009 RESTRAINTS Seat Belt - Tundra
w/o Power Seat:
OCCUPANT CLASSIFICATION ECU TERMINALS VOLTAGE CHART (W/O POWER
SEAT)
If the result is not as specified, the ECU may have a malfunction.
DATA LIST / ACTIVE TEST
1. READ DATA LIST
HINT:
Using Techstream to read the Data List allows the values or states of switches, sensors, actuators and
other items to be read without removing any parts. This non-intrusive inspection can be very useful
because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading
the Data List information early in troubleshooting is one way to save diagnostic time.
a. Connect Techstream to the DLC3.
b. Turn the ignition switch ON.
c. Turn the tester ON.
d. Enter the following menus:
Y2-4 (FSR-) - Y2-8
(FSR+)
B - W
Pressure sensor signal line
Ignition switch
ON
Below 1 to 5 V
Y2-9 (BSW) - Y2-5
(BGND)
L - O
Passenger side buckle
switch line
Ignition switch
ON
Pulse generation
Y2-3 (GND) - Body
ground
W-B - Body
ground
Ground
Always
Below 1 ohms
Terminal No.
(Symbols)
Wiring Color
Terminal Description
Condition
Specified
Condition
Q11-1 (+B) - Body
ground
R - Body
ground
Power source
Always
11 to 14 V
Q11-7 (IG) - Body
ground
SB - Body
ground
Occupant classification
ECU +B line
Ignition switch
ON
11 to 14 V
Q11-4 (FSR-) - Q11-8
(FSR+)
B - W
Pressure sensor signal line
Ignition switch
ON
Below 1 to 5 V
Q11-9 (BSW) - Q11-5
(BGND)
L - O
Passenger side buckle
switch line
Ignition switch
ON
Pulse generation
Q11-3 (GND) - Body
ground
W-B - Body
ground
Ground
Always
Below 1 ohms
NOTE:
In the table below, the values listed under "Normal Condition" are
reference values. Do not depend solely on these reference values when
deciding whether a part is faulty or not.
2009 Toyota Tundra
2009 RESTRAINTS Seat Belt - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст