Toyota Tundra. Manual — part 953
Fig. 108: Identifying Auto LSD Indicator Light Remains On - Wiring Diagram
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
INSPECTION PROCEDURE
1. INSPECT CAN COMMUNICATION SYSTEM
a. Check if a CAN communication system DTC is output (See DIAGNOSTIC TROUBLE CODE
TABLE ).
Result
RESULT TABLE
NOTE:
When replacing the VSC actuator assembly, perform zero point calibration (See
CALIBRATION ).
Result
Proceed to
2009 Toyota Tundra
2009 BRAKES Brake Control - Tundra
B: GO TO CAN COMMUNICATION SYSTEM (See HOW TO PROCEED WITH
TROUBLESHOOTING )
A: Go To Next Step
2. PERFORM ACTIVE TEST USING TECHSTREAM (AUTO LSD INDICATOR LIGHT)
a. Connect the Techstream to the DLC3.
b. Turn the ignition switch to ON.
c. Turn the Techstream on.
d. Select the Active Test mode and operate the AUTO LSD indicator light using the Techstream.
ABS/VSC/TRAC
DIAGNOSTIC NOTE TABLE
e. Check that the AUTO LSD indicator light turns on and off in the combination meter when using
the Techstream.
OK: The AUTO LSD indicator light turns on and off in accordance with the Techstream
operation.
HINT:
When the AUTO LSD indicator light remains illuminated, there may be an open in the wire harness
of the combination meter or abnormalities in the meter circuit.
NG: GO TO METER/GAUGE SYSTEM (See HOW TO PROCEED WITH
TROUBLESHOOTING )
OK: Go To Next Step
3. INSPECT VSC OFF SWITCH
a. Remove the VSC OFF switch (See REMOVAL ).
b. Measure the resistance according to the value (s) in the table below.
Standard Resistance
TESTER CONNECTION SPECIFIED CONDITION TABLE
DTC is not output
A
DTC is output
B
Tester Display
Test Part
Control Range
Diagnostic Note
Auto LSD Indicator
Light
AUTO LSD indicator
light
ON/OFF
Observe combination
meter
2009 Toyota Tundra
2009 BRAKES Brake Control - Tundra
Fig. 109: Identifying VSC Off Switch
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPLACE VSC OFF SWITCH (See REMOVAL )
OK: Go To Next Step
4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
a. Disconnect the A17 ECU connector.
b. Disconnect the J22 switch connector.
c. Measure the resistance according to the value (s) in the table below.
Standard Resistance
TESTER CONNECTION SPECIFIED CONDITION TABLE
Tester Connection
Switch Condition
Specified Condition
6-9
Switch is pressed
Below 1 ohms
Switch is not pressed
10 kohms or higher
Tester Connection
Condition
Specified Condition
A17-13 (CSW) - J22-9
Always
Below 1 ohms
A17-13 (CSW) - Body ground
Always
10 kohms or higher
2009 Toyota Tundra
2009 BRAKES Brake Control - Tundra
Fig. 110: Identifying A17 ECU Connector & J22 Switch Connector
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
NG: REPAIR OR REPLACE HARNESS OR CONNECTOR
OK: REPLACE VSC ACTUATOR ASSEMBLY (See REMOVAL )
AUTO LSD INDICATOR LIGHT DOES NOT COME ON
WIRING DIAGRAM
Refer to AUTO LSD INDICATOR LIGHT REMAINS ON .
INSPECTION PROCEDURE
1. INSPECT CAN COMMUNICATION SYSTEM
a. Check if a CAN communication system DTC is output (See DIAGNOSTIC TROUBLE CODE
TABLE ).
Result
RESULT TABLE
NOTE:
When replacing the VSC actuator assembly, perform zero point calibration (See
CALIBRATION ).
Result
Proceed to
2009 Toyota Tundra
2009 BRAKES Brake Control - Tundra
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст