Toyota Sequoia (2005). Manual — part 751
Z04244
Matchmarks
Matchmarks
PR07O–02
Z16099
PR0019
SST
A
Z04246
SST
PR–10
–
PROPELLER SHAFT
SPIDER BEARING
2993
SPIDER BEARING
REPLACEMENT
1.
PLACE MATCHMARKS ON SHAFT AND YOKE
2.
REMOVE SNAP RING
(a)
Using a brass bar and a hammer, slightly tap in the bear-
ing outer race.
(b)
4WD rear propeller shaft:
Using 2 screwdrivers, remove the 4 snap rings from the
grooves.
(c)
2WD and 4WD front propeller shaft:
Using needle nose pliers, remove the 4 snap rings from
the grooves.
3.
REMOVE SPIDER BEARING
(a)
Using SST, push out the bearing from the flange yoke.
SST
09332–25010
HINT:
Sufficiently raise the part indicated by ”A” so that it does not
come into contact with the bearing.
(b)
Clamp the bearing outer race in a vise and tap off the
flange with a hammer.
HINT:
Remove the bearing on the opposite side in the same proce-
dure.
(c)
Install the 2 removed bearing outer races to the spider,
and clamp them in a vise.
(d)
Using SST, push out the bearing from the sleeve yoke.
SST
09332–25010
(e)
Clamp the outer bearing race in a vise and tap off the yoke
with a hammer.
HINT:
Remove the bearing on the opposite side in the same proce-
dure.
F19908
Color
Bearing
Cap
Drill Mark
Yoke
Z00735
PR0027
SST
PR0028
–
PROPELLER SHAFT
SPIDER BEARING
PR–11
2994
4.
4WD, REAR PROPELLER SHAFT:
SELECT SPIDER BEARING
Select an appropriate bearing according to the drill mark on the
yoke.
Yoke
Bearing
With drill mark
With color mark (White)
No drill mark
No color mark
5.
INSTALL SPIDER BEARING
(a)
Apply MP grease to a new spider and bearings.
HINT:
Be careful not to apply too much grease.
(b)
Align the matchmarks on the yoke and shaft.
(c)
Fit the spider into the yoke.
(d)
Using SST, install the bearing on the spider.
SST
09332–25010
(e)
Using SST, adjust both bearings so that the snap ring
grooves are at maximum and equal in width.
F07987
R16053
PR–12
–
PROPELLER SHAFT
SPIDER BEARING
2995
6.
INSTALL SNAP RINGS
(a)
Install 2 new snap rings of equal thickness which will allow
for 0 to 0.05 mm (0 to 0.0020 in.) axial play.
HINT:
Do not reuse the snap rings.
4WD rear propeller shaft:
Color
Mark
Thickness mm (in.)
None
–
2.00 (0.0784)
Light brown
–
2.03 (0.0799)
Blue
–
2.06 (0.0811)
None
–
2.09 (0.0823)
–
1
1.99 (0.0783)
–
2
2.01 (0.0791)
–
3
2.03 (0.0799)
–
4
2.05 (0.0807)
–
5
2.07 (0.0815)
–
6
2.09 (0.0823)
–
7
2.11 (0.0831)
–
8
2.13 (0.0839)
–
9
2.15 (0.0846)
–
10
2.17 (0.0854)
2WD and 4WD front propeller shaft:
Color
Thickness mm (in.)
Blue
1.638 (0.0645)
Yellow
1.588 (0.0625)
Silver
1.537 (0.0605)
Copper
1.511 (0.0595)
Black
1.486 (0.0585)
Red
1.435 (0.0565)
Green
1.384 (0.0545)
(b)
Using a hammer, tap the yoke until there is no clearance
between the bearing outer race and snap ring.
R04428
F19333
SPIDER GREASE FITTING ASSEMBLY DIRECTION
FOR 4WD REAR PROPELLER SHAFT
No. 3
No. 4
Sleeve Yoke
No. 4
Sleeve Yoke
No. 3
Fill up the No. 3, 4 and sleeve yoke grease fittings with MP grease.
The figure on the left shows the locations
of the grease fittings from the front.
–
PROPELLER SHAFT
SPIDER BEARING
PR–13
2996
7.
CHECK SPIDER BEARING
(a)
Check that the spider bearing moves smoothly.
(b)
Check the spider bearing axial play.
Maximum bearing axial play: 0.05 mm (0.0020 in.)
HINT:
Install new spider bearings on the flange side in the pro-
cedure described above.
When replacing the rear propeller shaft spider on 4WD
vehicle, be sure that the grease fitting assembly hole is
facing in the direction shown in the illustration below.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст