Toyota Sequoia (2005). Manual — part 750
PR01M–05
F19351
Front propeller shaft:
Rear propeller shaft:
N·m ( kgf·cm, ft·lbf )
Non–reusable part
: Specified torque
74 (750, 54)
88 (897, 65)
Flange Yoke
Flange Yoke
Snap Ring
Spider Bearing
Spider
Snap Ring
Spider Bearing
Spider
Front Propeller Shaft
88 (897, 65)
Flange Yoke
Snap Ring
Spider Bearing
Spider
88 (897, 65)
Rear Propeller Shaft
Snap Ring
Spider Bearing
Spider
Flange Yoke
Grease Fitting
Grease Fitting
Sleeve Yoke
PR–6
–
PROPELLER SHAFT
PROPELLER SHAFT ASSEMBLY (4WD)
2989
PROPELLER SHAFT ASSEMBLY (4WD)
COMPONENTS
PR05N–04
Z15303
Matchmarks
Q07228
Matchmarks
F13575
Matchmarks
–
PROPELLER SHAFT
PROPELLER SHAFT ASSEMBLY (4WD)
PR–7
2990
REMOVAL
1.
REMOVE FRONT PROPELLER SHAFT
(a)
Place matchmarks on the differential and propeller shaft
flange.
(b)
Remove the 4 nuts, washers and bolts, and disconnect
the propeller shaft from the differential.
(c)
Suspend the front side of the propeller shaft.
(d)
Place matchmarks on the transfer and propeller shaft
flanges.
(e)
Remove the 4 nuts and washers.
(f)
Remove the propeller shaft from the transfer.
2.
REMOVE REAR PROPELLER SHAFT
(a)
Place matchmarks on the transfer and propeller shaft
flanges.
(b)
Remove the 4 nuts and washers, and disconnect the pro-
peller shaft from the transfer.
(c)
Suspend the front side of the propeller shaft.
(d)
Place matchmarks on the differential and propeller shaft
flanges.
(e)
Remove the 4 nuts, washers and bolts.
(f)
Remove the propeller shaft from the differential.
PR07M–02
Z04240
Z04241
PR–8
–
PROPELLER SHAFT
PROPELLER SHAFT ASSEMBLY (4WD)
2991
INSPECTION
NOTICE:
Be careful not to grip the propeller shaft tube too tightly in
a vise as this will cause deformation.
1.
INSPECT PROPELLER SHAFT AND INTERMEDIATE
SHAFT FOR DAMAGE OR RUNOUT
Using a dial indicator, check the runout of each shaft.
Maximum runout:
0.8 mm (0.031 in.)
If shaft runout is greater than the maximum, replace the shaft.
2.
INSPECT SPIDER BEARING
(a)
Inspect the spider bearing for wear or damage.
(b)
Using a dial indicator, check the spider bearing axial play
by turning the yoke of flange while holding the shaft tight-
ly.
Maximum bearing axial play: 0.05 mm (0.0020 in.)
If the spider bearing axial play exceeds the maximum, replace
the spider bearing (See page
).
PR07N–02
Z15303
Matchmarks
F13575
Matchmarks
Q07228
Matchmarks
–
PROPELLER SHAFT
PROPELLER SHAFT ASSEMBLY (4WD)
PR–9
2992
INSTALLATION
1.
INSTALL FRONT PROPELLER SHAFT
(a)
Align the matchmarks on the propeller shaft flanges and
differential, and connect the flanges with the 4 bolts,
washers and nuts.
(b)
Torque the 4 bolts.
Torque: 74 N·m (750 kgf·cm, 54 ft·lbf)
(c)
Align the matchmarks on the propeller shaft flanges and
transfer, and connect the flanges with the 4 washers and
nuts.
(d)
Torque the 4 nuts.
Torque: 88 N·m (897 kgf·cm, 65 ft·lbf)
2.
INSTALL REAR PROPELLER SHAFT
(a)
Align the matchmarks on the propeller shaft flanges and
differential, and connect the flanges with the 4 bolts,
washers and nuts.
(b)
Torque the 4 bolts.
Torque: 88 N·m (897 kgf·cm, 65 ft·lbf)
(c)
Align the matchmarks on the propeller shaft flanges and
transfer, and connect the flanges with the 4 washers and
nuts.
(d)
Torque the 4 nuts.
Torque: 88 N·m (897 kgf·cm, 65 ft·lbf)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст