Toyota Sequoia (2005). Manual — part 921
H24319
H24318
Hog Ring
H24321
Hog Ring
H24861
H24317
BO–120
–
BODY
FRONT SEAT (Power Adjuster Type)
3673
(c)
Turn up the seatback cover and install the hog rings.
11.
INSTALL SEATBACK COVER AND PAD
(a)
Install the seatback cover and pad to the seat frame as-
sembly.
(b)
Install the hog rings to the seat frame assembly.
(c)
Install the hog rings to the seat frame assembly.
(d)
w/ Side airbag:
Connect the seatback cover bracket to the seat frame as-
sembly with the nut.
Torque: 5.5 N·m (56 kgf·cm, 49 in.·lbf)
(e)
Close the fastener.
(f)
Install the hog rings to the seat frame assembly.
H24316
H24315
H24314
H24313
–
BODY
FRONT SEAT (Power Adjuster Type)
BO–121
3674
12.
INSTALL ARMREST ASSEMBLY
(a)
Install the spacer to the armrest assembly.
(b)
Install the armrest assembly, armrest lock plate and arm-
rest spacer with the bolt.
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
HINT:
Install the armrest lock plate as shown in the illustration.
(c)
Install the armrest cap.
13.
INSTALL POWER SWITCH
Install the power switch with the 3 screws.
14.
INSTALL LUMBAR SWITCH
Install the lumbar switch with the 2 screws to the seat cushion
outer shield.
15.
INSTALL FRONT SEAT INNER BELT
(a)
Install the front seat inner belt with the nut.
Torque: 42 N·m (430 kgf·cm, 32 ft·lbf)
(b)
Connect the connectors and wire harness clamps.
16.
INSTALL SEAT CUSHION LOWER SHIELD, SEAT
CUSHION OUTER SHIELD AND SEAT CUSHION IN-
NER SHIELD
(a)
Assemble the seat cushion lower shield and seat cushion
outer shield with the screw.
(b)
Perform the same procedure on the other side.
(c)
Connect the lumbar switch connector to the seat cushion
outer shield, and install the seat cushion lower shield, out-
er shield and inner shield.
(d)
Install the 2 screws to the seat cushion lower shield.
(e)
Install the screw to the seat cushion inner shield.
(f)
Install the 2 screws to the seat cushion outer shield.
H24312
BO–122
–
BODY
FRONT SEAT (Power Adjuster Type)
3675
(g)
Install the screw to the seat cushion outer shield.
(h)
Perform the same procedure on the seat cushion inner
shield.
17.
INSTALL SLIDE KNOB AND RECLINING KNOB
18.
INSTALL HEADREST
BO4S9–01
–
BODY
FRONT SEAT (Power Adjuster Type)
BO–123
3676
INSTALLATION
HINT:
The procedures listed below are for the LH side.
1.
INSTALL FRONT SEAT
(a)
Mount the front seat to the vehicle.
NOTICE:
Be careful not to damage the vehicle body.
(b)
w/ Side airbag:
Connect the airbag connector.
(c)
Connect the connectors.
(d)
Slide the front seat to the rearmost position.
(e)
Tighten the bolts on the front side temporarily, starting from the bolt on the inner side.
(f)
Tighten them completely.
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
(g)
Slide the front seat to the foremost position.
(h)
Tighten the bolts on the rear side temporarily, starting from the bolt on the inner side.
(i)
Tighten them completely.
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
2.
INSTALL SEAT TRACK COVERS
3.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
4.
Passenger ’s seat:
PERFORM PASSENGER OCCUPANT CLASSIFICATION SYSTEM ZERO POINT CALIBRATION
(See page
5.
PERFORM INITIALIZATION (See page
Some systems need initialization when disconnecting the cable from the negative battery terminal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст