Toyota Sequoia (2005). Manual — part 920
H24327
BO–116
–
BODY
FRONT SEAT (Power Adjuster Type)
3669
16.
REMOVE RH AND LH SEATBACK SHIELDS
(a)
Remove the 2 screws and RH seatback shield.
(b)
Perform the same procedure on the other side.
17.
REMOVE VERTICAL ADJUSTER BRACKET INNER
AND OUTER COVERS
(a)
Remove the screw and vertical adjuster bracket inner
cover.
(b)
Perform the same procedure on the other side.
18.
Driver’s seat:
REMOVE SEAT POSITION SENSOR
(See page
BO4SA–01
H24327
H24326
H24325
–
BODY
FRONT SEAT (Power Adjuster Type)
BO–117
3670
REASSEMBLY
CAUTION:
Wear safety gloves, because the sharp edges and surfaces
of the seat frame may cause injury to the hands.
HINT:
The procedures listed below are for the LH side.
A bolt without a torque specification is shown in the stan-
dard bolt chart (see page
1.
Driver’s seat:
INSTALL SEAT POSITION SENSOR
(SEE PAGE
)
2.
INSTALL VERTICAL ADJUSTER BRACKET INNER
AND OUTER COVERS
(a)
Install the vertical adjuster bracket inner cover with the
screw.
(b)
Perform the same procedure on the other side.
3.
INSTALL RH AND LH SEATBACK SHIELDS
(a)
Install the RH seatback shield with the 2 screws.
(b)
Perform the same procedure on the other side.
4.
INSTALL RH AND LH RECLINING ADJUSTER INSIDE
COVERS
(a)
Connect the wire harness clamp.
(b)
Install the RH reclining adjuster inside cover with the
screw.
(c)
Perform the same procedure on the other side.
5.
INSTALL LUMBAR SUPPORT ADJUSTER
(a)
Install a new bushing to the lumbar support adjuster.
(b)
Install the lumbar support adjuster with the 2 screws.
H24324
H24394
Listing Pocket
Seat Wire
Seat Heater
Tack Pin
Seat Cushion Cover
A: Install the tack pins under the wire.
A
Seat Heater Strap
Tack pins should not be beyond the seat.
Front
Name Stamp
a–a:
Tack Pin
Seat Heater
b–b:
Tack Pin
Seat Heater
Seat Cushion Cover
Tack Pin
a
b
a
b
a
a
b
b
b
b
b
b
b
b
b
b
b
b
b
b
H24395
BO–118
–
BODY
FRONT SEAT (Power Adjuster Type)
3671
(c)
Engage the seatback spring edge with the seat frame as-
sembly.
6.
w/ Seat heater:
INSTALL SEAT CUSHION HEATER ASSEMBLY
(a)
Set the seat cushion heater assembly with the name
stamp side facing the seat cushion cover.
(b)
Install the seat cushion heater assembly with the 10 tack
pins.
NOTICE:
Do not substitute other metal parts for tack pins.
7.
INSTALL SEAT CUSHION COVER
Install the seat cushion cover to the seat cushion pad with the
hog rings.
HINT:
When installing the hog rings, take as much care as possible to
prevent wrinkles.
8.
INSTALL SEAT CUSHION COVER AND PAD
(a)
Install the seat cushion cover with seat cushion pad, and
latch the seat cushion cover hooks.
H24378
H24320
H24393
Listing Pocket
Seat Wire
Seat Heater
Tack Pin
Seatback Cover
A: Install the tack pins under the wire.
A
Tack pins should not be beyond the seat.
Upper
Name Stamp
a–a:
Tack Pin
Seat Heater
b–b:
Tack Pin
Seat Heater
Tack Pin
a
b
a
b
Seatback Cover
a
a
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
b
–
BODY
FRONT SEAT (Power Adjuster Type)
BO–119
3672
(b)
Install the hog rings to the seat cushion cover.
(c)
Install the 2 clips.
(d)
Connect the wire harness clamp.
9.
w/ Seat heater:
INSTALL SEATBACK HEATER ASSEMBLY
(a)
Set the seatback heater assembly with the name stamp
side facing the seatback cover.
(b)
Install the seatback heater assembly with the 11 tack
pins.
NOTICE:
Do not substitute other metal parts for tack pins.
10.
INSTALL SEATBACK COVER
(a)
Install the seatback cover to the seatback pad.
(b)
Install the 2 headrest supports.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст