Toyota Sequoia (2005). Manual — part 725
ST094–06
B02289
Terminal 50
Battery
Terminal C
B02290
Battery
Terminal C
Disconnect
B02291
Disconnect
Battery
B02292
Terminal 30
Battery
Ammeter
Terminal 50
–
STARTING
STARTER
ST–15
2889
TEST
NOTICE:
These tests must be done within 3 to 5 seconds to avoid the
coil to be burned – out.
1.
DO PULL–IN TEST
(a)
Disconnect the field coil lead wire from terminal C.
(b)
Connect the battery to the magnetic switch as shown.
Check that the pinion gear moves outward.
2.
DO HOLDING TEST
While connected as above with the pinion gear out, disconnect
the negative (–) lead from terminal C. Check that the pinion gear
remains out.
3.
INSPECT CLUTCH PINION GEAR RETURN
Disconnect the negative (–) lead from the starter body. Check
that the pinion gear returns inward.
4.
DO NO–LOAD PERFORMANCE TEST
(a)
Connect the battery and ammeter to the starter as shown.
(b)
Check that the starter rotates smoothly and steadily with
the pinion gear moving out. Check that the ammeter
shows the specified current.
Specified current:
At 11.5 V: 100 A or less
ST095–06
B04549
Starter
Connector
Engine Wire Protector
B04548
ST–16
–
STARTING
STARTER
2890
INSTALLATION
1.
INSTALL STARTER
(a)
Install the engine wire protector to the starter with the bolt.
Torque: 9.81 N·m (100 kgf·cm, 84 in.·lbf)
(b)
Connect the starter wire with the nut.
Torque: 9.81 N·m (100 kgf·cm, 84 in.·lbf)
(c)
Connect the starter connector.
(d)
Connect the starter to the cylinder block.
(e)
Connect the engine wire with the bolt.
(f)
Install the starter with the 2 bolts.
Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
2.
INSTALL AIR PUMP ASSEMBLY (See page
)
3.
INSTALL INTAKE MANIFOLD ASSEMBLY
(See page
4.
CONNECT THROTTLE BODY ASSEMBLY TO INTAKE
MANIFOLD (See page
5.
INSTALL INTAKE AIR CONNECTOR
6.
INSTALL THROTTLE BODY COVER
7.
CONNECT CABLE TO NEGATIVE (–) BATTERY TER-
MINAL
8.
PERFORM INITIALIZATION (See page
)
Some system need initialzation when disconnecting the cable
from the battery terminal.
ST0PJ–01
A00968
Continuity
No continuity
1
2
5
3
Ohmmeter
Ohmmeter
A00969
Ohmmeter
Battery
1
2
5
3
Continuity
–
STARTING
STARTER RELAY
ST–17
2891
STARTER RELAY
INSPECTION
1.
REMOVE STARTER RELAY
Remove the relay box cover and starter relay.
2.
INSPECT STARTER RELAY CONTINUITY
(a)
Using an ohmmeter, check that there is continuity be-
tween terminals 1 and 2.
If there is no continuity, replace the relay.
(b)
Check that there is no continuity between terminals 3 and
5.
If there is continuity, replace the relay.
3.
INSPECT STARTER RELAY OPERATION
(a)
Apply battery positive voltage across terminals 1 and 2.
(b)
Using an ohmmeter, check that there is continuity be-
tween terminals 3 and 5.
If there is no continuity, replace the relay.
4.
REINSTALL STARTER RELAY
ST0OT–02
S04972
Continuity
No continuity
1
2
5
3
Ohmmeter
Ohmmeter
Continuity
4
S04971
Ohmmeter
Battery
1
2
5
3
Continuity
Ohmmeter
No Continuity
4
ST–18
–
STARTING
ACC CUT RELAY
2892
ACC CUT RELAY
INSPECTION
1.
REMOVE ACC CUT RELAY
Remove the cowl side trim board LH and ACC cut relay.
2.
INSPECT ACC CUT RELAY CONTINUITY
(a)
Using an ohmmeter, check that there is continuity be-
tween terminals 1 and 2.
If there is no continuity, replace the relay.
(b)
Check that there is no continuity between terminals 3 and
5.
If there is continuity, replace the relay.
(c)
Check that there is continuity between terminals 3 and 4.
If there is no continuity, replace the relay.
3.
INSPECT ACC CUT RELAY OPERATION
(a)
Apply battery positive voltage across terminals 1 and 2.
(b)
Using an ohmmeter, check that there is no continuity be-
tween terminals 3 and 4.
If there is continuity, replace the relay.
(c)
Using an ohmmeter, check that there is continuity be-
tween terminals 3 and 5.
If there is no continuity, replace the relay.
4.
REINSTALL ACC CUT RELAY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст