Toyota Sequoia (2005). Manual — part 812
SR1HO–08
F16015
Steering Wheel
Masking Tape
Steering Column
Upper Cover
F16016
Steering Column
Upper Cover
Marked Line
Steering
Wheel
Masking
Tape
SR–10
–
STEERING
STEERING WHEEL
3237
REPAIR PROCEDURES
HINT:
This is the repair procedure for steering off center.
1.
INSPECT STEERING WHEEL OFF CENTER
(a)
Apply masking tape on the top center of the steering
wheel and steering column upper cover.
(b)
Drive the vehicle in a straight line for 100 meters at a
constant speed of 35 mph (56 km/h), and hold the steer-
ing wheel to maintain the course.
(c)
Draw a line on the masking tape as shown in the illustra-
tion.
F16017
Steering Column
Upper Cover
New Marked
Line
Steering Wheel
R00429
Marked Line
F16018
–
STEERING
STEERING WHEEL
SR–11
3238
(d)
Turn the steering wheel to its straight position.
HINT:
Refer to the upper surface of the steering wheel, steering spoke
and SRS airbag line for the straight position.
(e)
Draw a new line on the masking tape of the steering wheel
as shown in the illustration.
(f)
Measure the distance between the 2 lines on the masking
tape of the steering wheel.
(g)
Convert the measured distance to steering angle.
Measured distance 1 mm (0.04 in.) = Steering angle
approximately 1 deg.
HINT:
Make a note of the steering angle.
2.
ADJUST STEERING ANGLE
(a)
Draw a line on the RH and LH tie rod and rack ends where
it can easily be seen.
(b)
Using a paper gauge, measure the distance from RH and
LH tie rod ends to the rack end screws.
HINT:
Measure the RH side and LH side.
Make a note of the measured values.
(c)
Remove the RH and LH boot clips from the rack boots.
(d)
Loosen the RH and LH lock nuts.
(e)
Turn the RH and LH rack end by the same amount (but
in different directions) according to the steering angle.
1 turn 360 deg. of rack end (1.5 mm (0.059 in.) horizon-
tal movement) = 12 deg. of steering angle
(f)
Tighten the RH and LH lock nuts.
Torque: 55 N·m (560 kgf·cm, 41 ft·lbf)
NOTICE:
Make sure that the difference in length between RH and LH
tie rod ends and rack end screws are within 1.5 mm (0.059
in.).
(g)
Install the RH and LH boot clips.
SR1F3–03
F17895
Steering Wheel Pad
Steering
Wheel
Column Lower
Cover
Combination
Switch
Steering Column Assembly
Transmission Control
Cable Assembly
Lower LH Finish Panel
Column Hole
Cover No. 2
No. 2 Universal
Joint Assembly
No. 2 Heater to Register Dust
Torx
®
Screw
35 (360, 26)
35 (360, 26)
8.0 (82, 71 in.·lbf)
26 (260, 19)
26 (260, 19)
8.8 (90, 78 in.·lbf)
50 (510, 37)
8.8 (90, 78 in.·lbf)
Front Door Scuff Plate
Cowl Side Trim
Hood Lock
Release Lever
8.0 (82, 71 in.·lbf)
Side Panel
No. 2 Intermediate
Shaft Assembly
Brake Pedal
Return Spring
Column Upper Cover
N·m (kgf·cm, ft·lbf) : Specified torque
Steering Wheel Lower
No. 3 Cover
Steering Wheel Lower
No. 2 Cover
35 (360, 26)
Sliding Yoke
Torx
®
Screw
SR–12
–
STEERING
TILT STEERING COLUMN
3239
TILT STEERING COLUMN
COMPONENTS
F13256
Non–reusable part
Molybdenum disulfide lithium base grease
: Specified torque
N·m (kgf·cm, ft·lbf)
Column Upper
Bracket
Key Cylinder
Key Unlock
Warning Switch
Ignition Switch
10.5 (110, 8)
Column Tube
Assembly
2.2 (23, 19 in.·lbf)
Spring Guide
Tilt Spring
Main Shaft Assembly
Steering Column Housing
Tilt Lever
Release Lever Spring
Turn Signal Bracket
Compression
Spring
Spring
Retainer
Upper Bearing Inner Race Seat
Inner Race
12 (120, 9)
Pivot Pin
Spring
Park Lock Cable
Assembly
Shaft Bearing
Main Shaft Stopper
Pivot Pin
Shift Lever
Housing
18 (180, 13)
Shift Lever
No. 2 Steering Column Ring
Tilt Lever Lock Shaft
9.0 (90, 78 in.·lbf)
7.5 (75, 65 in.·lbf)
2.9 (29, 25 in.·lbf)
Transponder Key Coil
Key Cylinder
Lamp Assembly
Screw
Transponder Key Amplifier
Tilt No. 1
Stopper
–
STEERING
TILT STEERING COLUMN
SR–13
3240
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст