Toyota Sequoia (2005). Manual — part 759
SA24P–03
F07264
R13372
SST
R13373
Washer
Nut
–
SUSPENSION AND AXLE
FRONT WHEEL HUB BOLT
SA–29
3025
FRONT WHEEL HUB BOLT
REPLACEMENT
1.
REMOVE FRONT WHEEL
2.
REMOVE BRAKE CALIPER AND DISC
(a)
Remove the bolt and brake line clamp from the steering
knuckle.
(b)
Remove the 2 bolts, brake caliper and disc.
(c)
Support the brake caliper securely.
3.
REMOVE HUB BOLT
Using SST and a screwdriver or an equivalent, remove the hub
bolt.
SST
09650–17011
4.
INSTALL HUB BOLT
(a)
Install a washer and nut to a new hub bolt as shown in the
illustration.
(b)
Using a screwdriver or an equivalent to hold, install the
hub bolt by torquing the nut.
(c)
Remove the nut and washer.
5.
INSTALL BRAKE DISC AND CALIPER
(a)
Install the brake disc, caliper and 2 bolts.
Torque: 123 N·m (1,250 kgf·cm, 90 ft·lbf)
(b)
Install the brake line clamp to the steering knuckle with the
bolt.
Torque: 28 N·m (285 kgf·cm, 21 ft·lbf)
6.
INSTALL FRONT WHEEL
Torque: 110 N·m (1,150 kgf·cm, 83 ft·lbf)
7.
DEPRESS BRAKE PEDAL SEVERAL TIMES
SA14E–08
F06645
Snap Ring
Drive Shaft
Dust Cover
Inboard Joint Shaft
Inboard Joint Boot
Outboard Joint Boot
Boot Clamp
Dust Seal
Outboard Joint Shaft
Cotter Pin
Cotter Pin
Grease Cap
Lock Cap
Lock Nut
235 (2,400, 173)
140 (1,450, 103)
Non–reusable part
N·m (kgf·cm, ft·lbf) : Specified torque
Shock Absorber
with Coil Spring
135 (1,400, 100)
LH side:
64 (650, 47)
SA–30
–
SUSPENSION AND AXLE
FRONT DRIVE SHAFT
3026
FRONT DRIVE SHAFT
COMPONENTS
SA24L–03
F06624
R12863
SST
R13233
–
SUSPENSION AND AXLE
FRONT DRIVE SHAFT
SA–31
3027
REMOVAL
1.
REMOVE FRONT WHEEL
2.
REMOVE ENGINE UNDER COVER
3.
DRAIN DIFFERENTIAL OIL
4.
REMOVE DRIVE SHAFT LOCK NUT
(a)
Using a screwdriver and hammer, remove the grease cap.
(b)
Remove the cotter pin and lock cap.
(c)
While applying the brakes, remove the lock nut.
5.
DISCONNECT LOWER SUSPENSION ARM FROM
LOWER BALL JOINT
(a)
Remove the cotter pin and nut.
(b)
Using SST, disconnect the lower suspension arm from the
lower ball joint.
SST
09628–62011
6.
DISCONNECT DRIVE SHAFT FROM STEERING
KNUCKLE
(a)
Using a plastic hammer, disengage the drive shaft from
the axle hub.
(b)
Push the steering knuckle outward and disconnect the
drive shaft from the steering knuckle.
NOTICE:
Be careful not to damage the oil seal, boots and dust seal.
7.
LH drive shaft:
REMOVE LH SHOCK ABSORBER (See page
F07267
SST
LH:
RH:
SST
SA–32
–
SUSPENSION AND AXLE
FRONT DRIVE SHAFT
3028
8.
REMOVE DRIVE SHAFT
(a)
RH drive shaft:
Using a brass bar and hammer, remove the RH drive
shaft.
NOTICE:
Be careful not to damage the dust cover and oil seal.
(b)
LH drive shaft:
Using SST, remove the LH drive shaft.
SST
09520–01010, 09520–24010 (09520–32040)
NOTICE:
Be careful not to damage the dust cover and oil seal.
(c)
Using a screwdriver, remove the snap ring from the in-
board joint shaft.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст