Toyota Sequoia (2005). Manual — part 727
CH073–08
B16569
Generator Connector
Generator Wire
N·m (kgf·cm, ft·lbf) : Specified torque
39 (400, 29)
Engine Under Cover
x 5
Drive Belt
Wire Clamp
PS Vane Pump
39 (400, 29)
Terminal Cap
Intake Air Connector
Throttle Body Cover
39 (400, 29)
39 (400, 29)
15.5 (158, 11)
Generator
9.8 (100, 87 in.·lbf)
–
CHARGING
GENERATOR
CH–5
2897
GENERATOR
COMPONENTS
B16695
Pulley
Front Bearing
Bearing Retainer
Rear Bearing
Drive End Frame (Stator)
Rotor
Generator Washer
Bearing Cover
Rectifier End Frame
Terminal Insulator
Brush Holder
Non–reusable part
Rear End Cover
N·m (kgf·cm, ft·lbf) : Specified torque
110.3 (1,125, 81)
2.6 (27, 23 in.·lbf)
2.6 (27, 23 in.·lbf)
5.8 (59, 51 in.·lbf)
5.8 (59, 51 in.·lbf)
1.8 (18, 16 in.·lbf)
4.6 (47, 41 in.·lbf)
CH–6
–
CHARGING
GENERATOR
2898
CH0LY–02
B00809
–
CHARGING
GENERATOR
CH–7
2899
REMOVAL
1.
REMOVE ENGINE UNDER COVER
2.
REMOVE THROTTLE BODY COVER
3.
DISCONNECT CABLE FROM NEGATIVE (–) BATTERY
TERMINAL
4.
DISCONNECT INTAKE AIR CONNECTOR FROM
THROTTLE BODY
5.
REMOVE DRIVE BELT
Loosen the belt tension by turning the belt tensioner counter-
clockwise, and remove the drive belt.
HINT:
The pulley bolt for the belt tensioner has a left hand thread.
6.
REMOVE PS VANE PUMP FROM ENGINE
(See page
7.
REMOVE GENERATOR
(a)
Disconnect the generator connector.
(b)
Remove the terminal cap and nut, and disconnect the
generator wire.
(c)
Disconnect the wire clamp from the cord clip on the gener-
ator.
(d)
Remove the bolt, the 2 nuts and the generator.
CH0LZ–02
B16358
B16369
SST (B)
SST (A)
Turn
B16371
SST (C)
SST (B)
Insert
B16372
SST (C)
SST (A)
Turn
B16370
Turn
SST (A)
SST (B)
CH–8
–
CHARGING
GENERATOR
2900
DISASSEMBLY
1.
REMOVE REAR END COVER
(a)
Remove the 3 nuts the and end cover.
(b)
Remove the terminal insulator.
2.
REMOVE BRUSH HOLDER
(a)
Remove the 2 screws and brush holder.
3.
REMOVE PULLEY
(a)
Hold SST (A) with a torque wrench, and tighten SST (B)
clockwise to the specified torque.
SST
09820–63011
Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
(b)
Check that SST (A) is secured to the rotor shaft.
(c)
Mount SST (C) in a vise.
(d)
Insert SST (B) into SST (C), and attach the pulley nut to
SST (C).
(e)
To loosen the pulley nut, turn SST (A) in the direction
shown in the illustration.
NOTICE:
To prevent damage to the rotor shaft, do not
loosen the pulley nut more than one–half of a turn.
(f)
Remove the generator from SST (C).
(g)
Turn SST (B), and remove SST (A and B).
(h)
Remove the pulley nut and pulley.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст