Toyota Highlander Hybrid (2022 year). Manual in english — page 11
173
3-4. Adjusting the steering wheel and mirrors
3
Before driv
ing
If you notice any of the following symptoms, refer to the following
table for the likely cause and the solution.
If the symptom is not resolved by the solution, have the vehicle
inspected by your Toyota dealer.
NOTICE
• Do not apply hot water to the
camera in cold weather, as the
sudden change of temperature
may cause the camera to not
operate properly.
• When using a high pressure
washer to wash the vehicle, do
not directly spray the camera
and its surrounding area, as
doing so may cause the camera
to not operate properly.
●
Do not subject the camera to a
strong impact as this could
cause a malfunction.
If this happens, have the vehicle
inspected by your Toyota dealer
as soon as possible.
If you notice any symptoms
174
3-4. Adjusting the steering wheel and mirrors
Symptom
Likely cause
Solution
The image is diffi-
cult to see.
The mirror surface is dirty.
Clean the mirror surface
gently, using a soft dry
cloth.
Sunlight or headlights are
shining directly into the Dig-
ital Rearview Mirror.
Change to optical mirror
mode.
(If the light is coming
through the moon roof or
panoramic moon roof,
close the sunshade or
electronic sunshade.)
• The vehicle is in a dark
area.
• The vehicle is near a TV
tower, broadcasting sta-
tion, electric power plant,
or other location where
strong radio waves or
electrical noise may be
present.
• The temperature around
the camera is extremely
high/low.
• The ambient temperature
is extremely low.
• It is raining or humid.
• Sunlight or headlights are
shining directly into the
camera lens.
• The vehicle is under fluo-
rescent lights, sodium
lights, mercury lights, etc.
• Exhaust gas is obstruct-
ing the camera.
Change to optical mirror
mode.
(Change back to digital
mirror mode when the
conditions have
improved.)
175
3-4. Adjusting the steering wheel and mirrors
3
Before driv
ing
The image is diffi-
cult to see.
Foreign matters (such as
water droplets, snow, mud,
etc.) is on the camera lens.
Operate the dedicated
camera cleaning
washer and clean the
camera lens. (
Change to optical mir-
ror mode.
Rinse the camera with
a large quantity of
water, wipe it clean
with a soft cloth damp-
ened with water, and
then change back to
digital mirror mode.
The image is out of
alignment.
The back door is not fully
closed.
Fully close the back
door.
The camera or its surround-
ing area has received a
strong impact.
Change to optical mirror
mode and have the vehi-
cle inspected by your
Toyota dealer.
The display is dim
and
is dis-
played.
The system may be mal-
functioning.
Change to optical mirror
mode and have the vehi-
cle inspected by your
Toyota dealer.
goes off.
Symptom
Likely cause
Solution
176
3-4. Adjusting the steering wheel and mirrors
is displayed.
The Digital Rearview Mirror
is extremely hot.
(The display will gradually
become more dim. If the
temperature continues to
increase, the Digital Rear-
view Mirror will turn off.)
Reducing the cabin tem-
perature is recom-
mended to reduce the
temperature of the mir-
ror.
(
will disappear
when the mirror
becomes cool.)
If
does not disap-
pear even though the
mirror is cool, have the
vehicle inspected by
your Toyota dealer.
The lever cannot be
operated properly.
The lever may be malfunc-
tioning.
Change to optical mirror
mode and have the vehi-
cle inspected by your
Toyota dealer.
(To change to optical
mirror mode, press and
hold the menu button for
approximately 10 sec-
onds.)
Symptom
Likely cause
Solution
177
3-4. Adjusting the steering wheel and mirrors
3
Before driv
ing
1
To select a mirror to adjust,
turn the switch.
Left
Right
2
To adjust the mirror, operate
the switch.
Up
Right
Down
Left
■
Mirror angle can be adjusted
when
The power switch is in ACC or ON.
■
When the mirrors are fogged up
The outside rear view mirrors can
be cleared using the mirror defog-
gers. Turn on the rear window
defogger to turn on the outside rear
view mirror defoggers. (
■
Automatic adjustment of the
mirror angle (if equipped)
A desired mirror face angle can be
entered to memory and recalled
automatically by the driving position
memory. (
■
Linked mirror function when
reversing (if equipped)
When either “L” or “R” of the mirror
select switch is selected, the outside
rear view mirrors will automatically
angle downwards when the vehicle
is reversing in order to give a better
view of the ground.
To disable this function, select nei-
ther “L” nor “R”.
To set the mirror angle used when
the vehicle is reversing, adjust the
Outside rear view mir-
rors
The rear view mirror’s posi-
tion can be adjusted to
enable sufficient confirma-
tion of the rear view.
WARNING
■
Important points while driving
Observe the following precautions
while driving.
Failing to do so may result in loss
of control of the vehicle and cause
an accident, resulting in death or
serious injury.
●
Do not adjust the mirrors while
driving.
●
Do not drive with the mirrors
folded.
●
Both the driver and passenger
side mirrors must be extended
and properly adjusted before
driving.
Adjustment procedure
178
3-4. Adjusting the steering wheel and mirrors
mirror angle at a desired position
with the shift lever in R.
The adjusted angle will be memo-
rized and the mirror will automati-
cally tilt to the memorized angle
whenever the shift lever is shifted to
R from next time.
The memorized downward tilt posi-
tion of the mirror is linked to the nor-
mal position (angle adjusted with
the shift lever in other than R).
Therefore, if the normal position is
changed after adjustment, the tilt
position will also change.
When the normal position is
changed, readjust the angle in
reversing.
Push the mirror back in the
direction of the vehicle’s rear.
WARNING
■
When the mirror defoggers
are operating
Do not touch the rear view mirror
surfaces, as they can become
very hot and burn you.
Folding the mirrors
179
3-5. Opening, closing the windows and moon roof
3
Before driv
ing
3-5.Opening, closing the windows and moon roof
The power windows can be
opened and closed using the
switches.
Operating the switch moves the
windows as follows:
1
Closing
2
One-touch closing
*
3
Opening
4
One-touch opening
*
*
: To stop the window partway,
operate the switch in the opposite
direction.
■
The power windows can be
operated when
The power switch is in ON.
■
Operating the power windows
after turning the hybrid system
off
The power windows can be oper-
ated for approximately 45 seconds
even after the power switch is
turned to ACC or turned off. They
cannot, however, be operated once
either front door is opened.
■
Jam protection function
If an object becomes jammed
between the window and the win-
dow frame while the window is clos-
ing, window movement is stopped
and the window is opened slightly.
■
Catch protection function
If an object becomes caught
between the door and window while
the window is opening, window
movement is stopped.
■
When the window cannot be
opened or closed
When the jam protection function or
catch protection function operates
unusually and the door window can-
not be opened or closed, perform
the following operations with the
power window switch of that door.
●
Stop the vehicle. With the power
switch in ON, within 4 seconds of
the jam protection function or
catch protection function activat-
ing, continuously operate the
power window switch in the
one-touch closing direction or
one-touch opening direction so
that the door window can be
opened and closed.
●
If the door window cannot be
opened and closed even when
performing the above operations,
perform the following procedure
for function initialization.
1
Turn the power switch to ON.
2
Pull and hold the power window
switch in the one-touch closing
direction and completely close
the door window.
3
Release the power window
switch for a moment, resume
pulling the switch in the
one-touch closing direction, and
hold it there for approximately 6
seconds or more.
4
Press and hold the power win-
dow switch in the one-touch
opening direction. After the door
window is completely opened,
continue holding the switch for
an additional 1 second or more.
Power windows
Opening and closing the
power windows
180
3-5. Opening, closing the windows and moon roof
5
Release the power window
switch for a moment, resume
pushing the switch in the
one-touch opening direction, and
hold it there for approximately 4
seconds or more.
6
Pull and hold the power window
switch in the one-touch closing
direction again. After the door
window is completely closed,
continue holding the switch for a
further 1 second or more.
If you release the switch while the
window is moving, start again from
the beginning.
If the window reverses and cannot
be fully closed or opened, have the
vehicle inspected by your Toyota
dealer.
■
Door lock linked window opera-
tion
●
The power windows can be
opened and closed using the
mechanical key.
*
(
●
The power windows can be
opened using the wireless remote
control.
*
(
*
: These settings must be custom-
ized at your Toyota dealer.
■
Power windows open warning
buzzer
A buzzer sounds and a message is
shown on the multi-information dis-
play when the power switch is
turned off and the driver’s door is
opened with the power windows
open.
■
Customization
Some functions can be customized.
(
WARNING
Observe the following precau-
tions.
Failing to do so may result in
death or serious injury.
■
Closing the windows
●
The driver is responsible for all
the power window operations,
including the operation for the
passengers. In order to prevent
accidental operation, especially
by a child, do not let a child
operate the power windows. It is
possible for children and other
passengers to have body parts
caught in the power window.
Also, when riding with a child, it
is recommended to use the win-
dow lock switch. (
●
Check to make sure that all pas-
sengers do not have any part of
their body in a position where it
could be caught when a window
is being operated.
●
When using the wireless remote
control or mechanical key and
operating the power windows,
operate the power window after
checking to make sure that
there is no possibility of any
passenger having any of their
body parts caught in the win-
dow. Also do not let a child
operate window by the wireless
remote control or mechanical
key. It is possible for children
and other passengers to get
caught in the power window.
●
When exiting the vehicle, turn
the power switch off, carry the
key and exit the vehicle along
with the child. There may be
accidental operation, due to
mischief, etc., that may possibly
lead to an accident.
181
3-5. Opening, closing the windows and moon roof
3
Before driv
ing
This function can be used to
prevent children from acciden-
tally opening or closing a pas-
senger window.
Press the switch.
The indicator
will come on and
the passenger windows will be
locked.
The passenger windows can still be
opened and closed using the
driver’s switch even if the lock
switch is on.
■
The power windows can be
operated when
The power switch is in ON.
■
When the 12-volt battery is dis-
connected
The window lock switch is disabled.
If necessary, press the window lock
switch after reconnecting the 12-volt
battery.
WARNING
■
Jam protection function
●
Never use any part of your body
to intentionally activate the jam
protection function.
●
The jam protection function may
not work if something gets
jammed just before the window
is fully closed. Be careful not to
get any part of your body
jammed in the window.
■
Catch protection function
●
Never use any part of your body
or clothing to intentionally acti-
vate the catch protection func-
tion.
●
The catch protection function
may not work if something gets
caught just before the window is
fully opened. Be careful not to
get any part of your body or
clothing caught in the window.
Preventing accidental
operation (window lock
switch)
182
3-5. Opening, closing the windows and moon roof
*
: If equipped
■
Opening and closing
1
Opens the moon roof
*
The moon roof stops slightly before
the fully open position to reduce
wind noise. Press the switch again
to fully open the moon roof.
2
Closes the moon roof
*
*
: Lightly press either side of the
moon roof switch to stop the
moon roof partway.
■
Tilting up and down
1
Tilts the moon roof up
*
2
Tilts the moon roof down
*
*
: Lightly press either side of the
moon roof switch to stop the
moon roof partway.
■
The moon roof can be operated
when
The power switch is in ON.
■
Operating the moon roof after
turning the hybrid system off
The moon roof can be operated for
approximately 45 seconds after the
power switch is turned to ACC or
turned off. It cannot, however, be
operated once either front door is
opened.
■
Jam protection function
If an object is detected between the
moon roof and the frame while the
moon roof is closing or tilting down,
travel is stopped and the moon roof
opens slightly.
■
Sunshade
The sunshade can be opened and
closed manually. However, the sun-
shade will open automatically when
the moon roof is opened.
■
Door lock linked moon roof
operation
●
The moon roof can be opened
and closed using the mechanical
key.
*
(
●
The moon roof can be opened
using the wireless remote control.
*
(
*
: These settings must be custom-
ized at your Toyota dealer.
■
When the moon roof does not
close normally
Perform the following procedure:
●
If the moon roof closes but then
re-opens slightly
1
Stop the vehicle.
Moon roof
*
Use the overhead switches
to open and close the moon
roof and tilt it up and down.
Operating the moon roof
183
3-5. Opening, closing the windows and moon roof
3
Before driv
ing
2
Press and hold the “CLOSE”
switch.
*1
The moon roof will close, reopen
and pause for approximately 10 sec-
onds.
*2
Then it will close again, tilt
up and pause for approximately 1
second. Finally, it will tilt down, open
and close.
3
Check to make sure that the
moon roof is completely closed
and then release the switch.
●
If the moon roof tilts down but then
tilts back up
1
Stop the vehicle.
2
Press and hold the “UP” switch
*1
until the moon roof moves into
the tilt up position and stops.
3
Release the “UP” switch once
and then press and hold the “UP”
switch again.
*1
The moon roof will pause for
approximately 10 seconds in the tilt
up position.
*2
Then it will adjust
slightly and pause for approximately
1 second. Finally, it will tilt down,
open and close.
4
Check to make sure that the
moon roof is completely closed
and then release the switch.
*1
:If the switch is released at the
incorrect time, the procedure will
have to be performed again from
the beginning.
*2
:If the switch is released after the
above mentioned 10 second
pause, automatic operation will
be disabled. In that case, press
and hold the “CLOSE” or “UP”
switch, and the moon roof will tilt
up and pause for approximately 1
second. Then it will tilt down,
open and close. Check to make
sure that the moon roof is com-
pletely closed and then release
the switch.
If the moon roof does not fully close
even after performing the above
procedure correctly, have the vehi-
cle inspected by your Toyota dealer.
■
Moon roof open warning buzzer
A buzzer sounds and a message is
shown on the multi-information dis-
play when the power switch is
turned off and the driver’s door is
opened with the moon roof open.
■
Customization
Some functions can be customized.
(
WARNING
Observe the following precau-
tions.
Failing to do so may cause death
or serious injury.
■
Opening the moon roof
●
Do not allow any passengers to
put their hands or heads outside
the vehicle while it is moving.
●
Do not sit on top of the moon
roof.
■
Opening and closing the
moon roof
●
The driver is responsible for
moon roof opening and closing
operations.
In order to prevent accidental
operation, especially by a child,
do not let a child operate the
moon roof. It is possible for chil-
dren and other passengers to
have body parts caught in the
moon roof.
184
3-5. Opening, closing the windows and moon roof
WARNING
●
Check to make sure that all pas-
sengers do not have any part of
their body in a position where it
could be caught when the moon
roof is being operated.
●
When using the wireless remote
control or mechanical key and
operating the moon roof, oper-
ate the moon roof after checking
to make sure that there is no
possibility of any passenger
having any of their body parts
caught in the moon roof. Also,
do not let a child operate moon
roof by the wireless remote con-
trol or mechanical key. It is pos-
sible for children and other
passengers to get caught in the
moon roof.
●
When exiting the vehicle, turn
the power switch off, carry the
key and exit the vehicle along
with the child. There may be
accidental operation, due to
mischief, etc., that may possibly
lead to an accident.
■
Jam protection function
●
Never use any part of your body
to intentionally activate the jam
protection function.
●
The jam protection function may
not work if something gets
caught just before the moon
roof is fully closed. Also, the jam
protection function is not
designed to operate while the
switch is being pressed. Take
care so that your fingers, etc. do
not get caught.
185
3-5. Opening, closing the windows and moon roof
3
Before driv
ing
*
: If equipped
■
Opening and closing the
electronic sunshade
1
Opens the electronic sun-
shade
*
2
Closes the electronic sun-
shade
*
*
: Lightly press either side of the
sunshade switch to stop the elec-
tronic sunshade partway.
■
Tilting the panoramic moon
roof up and down
Tilt up (press)
*
If the panoramic moon roof is open,
pressing the switch closes it up to
the tilt-up position.
If the shade is closed past the
half-open position when the switch
is pressed, it will open up to the
half-open position.
To stop operation partway, quickly
slide and release the switch again.
Tilt down (press and hold)
The panoramic moon roof can
be tilted down only when it is in
the tilt-up position.
■
Opening and closing the
panoramic moon roof
Open (slide backward)
*
To stop operation partway, quickly
slide and release the switch again.
Close (slide forward)
*
The panoramic moon roof stops
at the tilt-up position.
Slide and hold the switch again
to fully close the panoramic
moon roof.
To stop operation partway, quickly
slide and release the switch again.
Panoramic moon roof
*
Use the overhead switches
to operate the panoramic
moon roof and electronic
sunshade.
Operating the panoramic
moon roof
186
3-5. Opening, closing the windows and moon roof
■
The panoramic moon roof can
be operated when
The power switch is in ON.
■
Operating the panoramic moon
roof after turning the hybrid
system off
The panoramic moon roof and elec-
tronic sunshade can be operated for
approximately 45 seconds after the
power switch is turned to ACC or
turned off. It cannot, however, be
operated once either front door is
opened.
■
Closing the shade when the
panoramic moon roof is open
1
Slide the shade switch forward.
The shade closes up to its
half-closed position and then the
panoramic moon roof closes up to
the tilt-up position.
2
Slide and hold the shade switch
again.
The panoramic moon roof closes as
long as the switch is being held.
After the panoramic moon roof is
fully closed, the shade will fully
close automatically.
■
Jam protection function
If an object is detected between the
panoramic moon roof and the frame
in the following situations, travel is
stopped and the panoramic moon
roof opens slightly:
●
The panoramic moon roof is clos-
ing or tilting down.
●
The electronic sunshade is clos-
ing.
■
When the panoramic moon roof
does not close normally
Perform the following procedure:
●
If the panoramic moon roof closes
but then re-opens slightly
1
Stop the vehicle.
2
Slide the panoramic moon roof
switch forward and hold it.
*
The panoramic moon roof will close
then reopen and pause for approxi-
mately 10 seconds. Then it will
close up to the tilt-up position.
3
Release the switch and then
slide it forward and hold it again.
The panoramic moon roof will close
as long as the switch is being held.
4
Check to make sure that the pan-
oramic moon roof is completely
closed and then release the
switch.
●
If the panoramic moon roof tilts
down but then tilts back up
1
Stop the vehicle.
2
Slide the panoramic moon roof
switch forward and hold it.
*
The panoramic moon roof will tilt
down then tilt up and pause for
approximately 10 seconds. Then it
will close.
3
Check to make sure that the pan-
oramic moon roof is completely
closed and then release the
switch.
*
: If the switch is released at the
incorrect time, the procedure will
have to be performed again from
the beginning.
If the panoramic moon roof does not
fully close even after performing the
above procedure correctly, have the
vehicle inspected by your Toyota
dealer.
■
When the shade does not close
normally
Perform the following procedure:
1
Stop the vehicle.
2
Close the panoramic moon roof.
187
3-5. Opening, closing the windows and moon roof
3
Before driv
ing
3
Slide the shade switch forward
and hold it.
*
The shade will close then reopen
and pause for approximately 10 sec-
onds. Then it will close.
4
Check to make sure that the
shade is completely closed and
then release the switch.
*
: If the switch is released at the
incorrect time, the procedure will
have to be performed again from
the beginning.
If the shade continues to close but
then reopens slightly even after per-
forming the above procedure cor-
rectly, have the vehicle inspected by
your Toyota dealer.
■
Panoramic moon roof open
warning buzzer
A buzzer sounds and a message is
shown on the multi-information dis-
play when the power switch is
turned off and the driver’s door is
opened with the panoramic moon
roof open.
WARNING
Observe the following precau-
tions.
Failing to do so may cause death
or serious injury.
■
Opening and closing the elec-
tronic sunshade
●
Check to make sure that all pas-
sengers do not have any part of
their body in a position where it
could be caught when the elec-
tronic sunshade is being oper-
ated.
●
Do not let a child operate the
electronic sunshade. Closing
the electronic sunshade on
someone can cause death or
serious injury.
■
Opening the panoramic moon
roof
●
Do not allow any passengers to
put their hands or heads outside
the vehicle while it is moving.
●
Do not sit on top of the pan-
oramic moon roof.
■
Opening and closing the pan-
oramic moon roof
●
The driver is responsible for
panoramic moon roof opening
and closing operations. In order
to prevent accidental operation,
especially by a child, do not let a
child operate the panoramic
moon roof. It is possible for chil-
dren and other passengers to
have body parts caught in the
panoramic moon roof.
188
3-5. Opening, closing the windows and moon roof
WARNING
●
Check to make sure that all pas-
sengers do not have any part of
their body in a position where it
could be caught when the pan-
oramic moon roof is being oper-
ated.
●
When exiting the vehicle, turn
the power switch off, carry the
key and exit the vehicle along
with the child. There may be
accidental operation, due to
mischief, etc., that may possibly
lead to an accident.
■
Jam protection function
●
Never use any part of your body
to intentionally activate the jam
protection function.
●
The jam protection function may
not work if something gets
caught just before the pan-
oramic moon roof or electronic
sunshade is fully closed. Also,
the jam protection function is
not designed to operate while
the switch is being pressed.
Take care so that your fingers,
etc. do not get caught.
■
To prevent burns or injuries
Do not touch the area between
the underside of the panoramic
moon roof and the electronic sun-
shade. Your hand may get caught
and you could injure yourself.
Also, if the vehicle is left in direct
sunlight for a long time, the under-
side of the panoramic moon roof
could become very hot and could
cause burns.
NOTICE
■
To prevent damage to the
panoramic moon roof
●
Before opening the panoramic
moon roof, make sure that there
are no foreign objects, such as
stones or ice, around the open-
ing.
●
Do not hit the surface or edge of
the panoramic moon roof with
hard objects.
■
After the vehicle has been
washed or rained on
Before opening the panoramic
moon roof, wipe any water off the
panoramic moon roof. Otherwise,
water may enter the cabin when
the panoramic moon roof is
opened.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст