Toyota Highlander Hybrid (2022 year). Manual in english — page 10
157
3-3. Adjusting the seats
3
Before driv
ing
2
Stow the second seat belt
buckles.
3
Pass the outer seat belts
through the seat belt hangers
and secure the seat belt
plates.
This prevents the shoulder belts
from being damaged.
4
Lower the head restraints to
the lowest position. (
■
Folding down the second
seats
1
Pull the seatback angle
adjustment lever or to
tilt the seatback forward.
Each seatback may be folded sep-
arately.
2
Pull the seatback folding
lever to unlock the seatback.
The seatback will be folded
down.
■
After folding down the sec-
ond seats
Slide the folded second seats
backward until they lock.
158
3-3. Adjusting the seats
■
Returning the second seats
Lift up the seatbacks until they
lock.
Remove the secured seat belts
from the seat belt hangers before
using them.
■
Before folding down the
third seats
1
Stow the third seat belt buck-
les.
2
Pass the outer seat belts
through the seat belt hangers
and secure the seat belt
plates.
This prevents the shoulder belts
from being damaged.
3
Lower the center head
restraint to the lowest posi-
tion. (
■
Folding down the third
seats
While pulling the the seatback
angle adjustment lever, fold
down the seatbacks.
The outer head restraints will fold
forward.
■
Returning the third seats
1
Returning the seatbacks
From inside
Lift up the seatbacks until they lock.
Folding down the third
seats
159
3-3. Adjusting the seats
3
Before driv
ing
From outside
Pull the straps and raise the seat-
backs until they lock.
After using either strap, use the vel-
cro on the strap to attach it to the
seatback.
2
Returning the outer head
restraints.
Remove the secured seat belts
from the seat belt hangers before
using them.
*
: If equipped
1
Check that the shift lever is in
P.
2
Turn the power switch to ON.
3
Adjust the driver’s seat, out-
side rear view mirrors and
head-up display (if equipped)
to the desired positions.
4
While pressing the “SET” but-
ton, or within 3 seconds after
the “SET” button is pressed,
press button “1” or “2” until
the buzzer sounds.
If the selected button has already
been preset, the previously
recorded position will be overwrit-
Driving position mem-
ory
*
This feature automatically
adjusts the driver’s seat,
outside rear view mirrors
and head-up display (if
equipped) to suit your pref-
erences.
Two different driving posi-
tions can be recorded into
memory.
Each electronic key can be
registered to recall your pre-
ferred driving position.
Recording a driving posi-
tion into memory
160
3-3. Adjusting the seats
ten.
■
Seat positions that can be
memorized
The adjusted positions other than
the position adjusted by lumbar sup-
port switch can be recorded.
■
In order to correctly use the
driving position memory func-
tion
If a seat position is already in the
furthest possible position and the
seat is operated in the same direc-
tion, the recorded position may be
slightly different when it is recalled.
1
Check that the shift lever is in
P.
2
Turn the power switch to ON.
3
Press one of the buttons for
the driving position you want
to recall until the buzzer
sounds.
■
To stop the position recall oper-
ation part-way through
Perform any of the following opera-
tions:
●
Press the “SET” button.
●
Press button “1” or “2”.
●
Operate any of the seat adjust-
ment switches (only cancels seat
position recall).
■
Operating the driving position
memory after turning the power
switch off
Recorded seat positions can be
activated up to 180 seconds after
the driver’s door is opened and
another 60 seconds after it is closed
again.
■
When the recorded seat posi-
tion cannot be recalled
The seat position may not be
recalled in some situations when the
seat position is recorded in a certain
range. For details, contact your Toy-
ota dealer.
■
Registering procedure
Record your driving position to
WARNING
■
Seat adjustment caution
Take care during seat adjustment
so that the seat does not strike
the rear passenger or squeeze
your body against the steering
wheel.
Recalling a driving posi-
tion
Registering/cancel-
ing/recall a driving posi-
tion to an electronic key
(memory recall function)
161
3-3. Adjusting the seats
3
Before driv
ing
button “1” or “2” before perform-
ing the following:
Carry only the key you want to
register, and then close the
driver’s door.
If 2 or more keys are in the vehicle,
the driving position cannot be
recorded properly.
1
Check that the shift lever is in
P.
2
Turn the power switch to ON.
3
Recall the driving position
that you want to record.
4
While pressing the recalled
button, press and hold the
door lock switch (either lock
or unlock) until the buzzer
sounds.
If the button could not be regis-
tered, the buzzer sounds continu-
ously for approximately 3 seconds.
■
Cancelation procedure
Carry only the key you want to
cancel and then close the
driver’s door.
If 2 or more keys are in the vehicle,
the driving position cannot be can-
celed properly.
1
Turn the power switch to ON.
2
While pressing the “SET” but-
ton, press and hold the door
lock switch (either lock or
unlock) until the buzzer
sounds twice.
If the button could not be canceled,
the buzzer sounds continuously for
approximately 3 seconds.
■
Recall procedure
Make sure that the doors are
locked before recalling the driv-
ing position. Carry the electronic
key that has been registered to
the driving position, and then
unlock and open the driver’s
door using the smart key system
or wireless remote control.
The driving position will move to the
recorded position.
If the driving position is in a position
that has already been recorded, the
seat and outside rear view mirrors
will not move.
■
Recalling the driving position
using the memory recall func-
tion
●
Different driving positions can be
registered for each electronic key.
Therefore, the driving position that
is recalled may be different
depending on the key being car-
ried.
●
If a door other than the driver’s
door is unlocked with the smart
key system, the driving position
cannot be recalled. In this case,
press the driving position button
which has been set.
■
Customization
Some functions can be customized.
(
162
3-3. Adjusting the seats
■
Front seats
1
Up
Pull the head restraints up.
2
Down
Push the head restraint down while
pressing the lock release button
.
■
Second seats
1
Up
Pull the head restraints up.
2
Down
Push the head restraint down while
pressing the lock release button
.
■
Third center seat
1
Up
Pull the head restraints up.
2
Down
Push the head restraint down while
pressing the lock release button
.
■
Adjusting the height of the head
restraints
Head restraints
Head restraints are provided
for all seats.
WARNING
■
Head restraint precautions
Observe the following precautions
regarding the head restraints.
Failure to do so may result in
death or serious injury.
●
Use the head restraints
designed for each respective
seat.
●
Adjust the head restraints to the
correct position at all times.
●
After adjusting the head
restraints, push down on them
and make sure they are locked
in position.
●
Do not drive with the head
restraints removed.
Adjusting a head restraint
163
3-3. Adjusting the seats
3
Before driv
ing
Make sure that the head restraints
are adjusted so that the center of
the head restraint is closest to the
top of your ears.
■
Adjusting the third center seat
head restraint
Always raise the head restraint one
level from the stowed position when
using.
■
When using the outboard third
seats
If a head restraint is folded forward,
make sure to return it to the upright
position. (
Pull the head restraint up while
pressing the lock release button
.
If the head restraint touches the
ceiling, making the removal difficult,
change the seat height or angle.
(
Front seats
Second seats
Third center seat
Align the head restraint with the
installation holes and push it
down to the lock position.
Press and hold the lock release
button when lowering the
head restraint.
Front seats
Removing the head
restraints
Installing the head
restraints
164
3-3. Adjusting the seats
Second seats
Third center seat
165
3-4. Adjusting the steering wheel and mirrors
3
Before driv
ing
3-4.Adjusting the steering wheel and mirrors
1
Hold the steering wheel and
push the lever down.
2
Adjust to the ideal position by
moving the steering wheel
horizontally and vertically.
After adjustment, pull the lever up
to secure the steering wheel.
Press on or close to the
mark.
Steering wheel
Adjustment procedure
WARNING
■
Caution while driving
Do not adjust the steering wheel
while driving.
Doing so may cause the driver to
mishandle the vehicle and cause
an accident, resulting in death or
serious injury.
■
After adjusting the steering
wheel
Make sure that the steering wheel
is securely locked.
Otherwise, the steering wheel
may move suddenly, possibly
causing an accident, and resulting
in death or serious injury. Also,
the horn may not sound if the
steering wheel is not securely
locked.
Sounding the horn
166
3-4. Adjusting the steering wheel and mirrors
*
: If equipped
The height of the rear view mir-
ror can be adjusted to suit your
driving posture.
Adjust the height of the rear
view mirror by moving it up and
down.
Manual anti-glare inside rear
view mirror
Reflected light from the head-
lights of vehicles behind can be
reduced by operating the lever.
Normal position
Anti-glare position
Auto anti-glare inside rear
view mirror
Responding to the level of
brightness of the headlights of
vehicles behind, the reflected
light is automatically reduced.
Turn the automatic anti-glare
function mode on/off
When the automatic anti-glare func-
tion is in ON mode, the indicator
illuminates. The function will set to
ON mode each time the power
switch is turned to ON.
Pressing the button turns the func-
tion to OFF mode. (The indicator
also turns off.)
Inside rear view mir-
ror
*
The rear view mirror’s posi-
tion can be adjusted to
enable sufficient confirma-
tion of the rear view.
Adjusting the height of
rear view mirror
WARNING
■
Caution while driving
Do not adjust the position of the
mirror while driving.
Doing so may lead to mishandling
of the vehicle and cause an acci-
dent, resulting in death or serious
injury.
Anti-glare function
167
3-4. Adjusting the steering wheel and mirrors
3
Before driv
ing
■
To prevent sensor error (vehi-
cles with auto anti-glare inside
rear view mirror)
To ensure that the sensors operate
properly, do not touch or cover
them.
*
: If equipped
Digital Rearview Mir-
ror
*
The Digital Rearview Mirror
is a system that uses the
camera on the rear of the
vehicle and displays its
image on the display of the
Digital Rearview Mirror.
The Digital Rearview Mirror
can be changed between
optical mirror mode and dig-
ital mirror mode by operat-
ing the lever.
The Digital Rearview Mirror
allows the driver to see the
rear view despite obstruc-
tions, such as the head
restraints or luggage, ensur-
ing rear visibility. Also, the
rear seats are not displayed
and privacy of the passen-
gers is enhanced.
WARNING
Observe the following precau-
tions.
Failure to do so may result in
death or serious injury.
■
Before using the Digital Rear-
view Mirror
●
Make sure to adjust the mirror
before driving. (
• Change to optical mirror mode
and adjust the position of the
Digital Rearview Mirror so that
the area behind your vehicle
can be viewed properly.
168
3-4. Adjusting the steering wheel and mirrors
Camera indicator
Indicates that the camera is operat-
ing normally.
Icon display area
Displays icons, adjusting gauge,
etc. (
Select button
Press to change the setting of the
item you want to adjust.
Menu button
Press to display the icon display
area and select the item you want
to adjust.
Lever
Operate to change between digital
mirror mode and optical mirror
mode.
Operate the lever to change
between digital mirror mode and
optical mirror mode.
1
Digital mirror mode
Displays an image of the area
behind the vehicle.
will illuminate in this mode.
2
Optical mirror mode
Turns off the display of the Digital
Rearview Mirror allows it to be used
as an optical mirror.
■
Digital mirror mode operating
condition
The power switch is turned to ON.
When the power switch is changed
from ON to OFF or ACC, the image
will disappear after several seconds.
■
When using the Digital Rear-
view Mirror in digital mirror
mode
●
If it is difficult to see the displayed
image due to light reflected off the
Digital Rearview Mirror, the cam-
era being dirty, or if lights of a
vehicle behind your vehicle or the
displayed image are bothering
you, change to optical mirror
mode.
●
When the back door is open, the
Digital Rearview Mirror image may
not display properly. Before driv-
ing, make sure the back door is
WARNING
• Change to digital mirror mode
and adjust the display settings.
●
As the range of the image dis-
played by the Digital Rearview
Mirror is different from that of
the optical mirror, make sure to
check this difference before
driving.
System components
Changing modes
169
3-4. Adjusting the steering wheel and mirrors
3
Before driv
ing
closed.
●
If the display is difficult to see due
to reflected light, close the sun-
shade for the moon roof or the
electronic sunshade for the pan-
oramic moon roof.
●
Any of the following conditions
may occur when driving in the
dark, such as at night. None of
them indicates that a malfunction
has occurred.
• Colors of objects in the displayed
image may differ from their actual
color.
• Depending on the height of the
lights of the vehicle behind, the
area around the vehicle may
appear white and blurry.
• Automatic image adjustment for
brighter surrounding image may
cause flickering.
If it is difficult to see the displayed
image or flickering bothers you,
change to optical mirror mode.
●
The Digital Rearview Mirror may
become hot while it is in digital
mirror mode.
This is not a malfunction.
●
Depending on your physical con-
dition or age, it may take longer
than usual to focus on the dis-
played image. In this case,
change to optical mirror mode.
●
Do not let passengers stare at the
displayed image when the vehicle
is being driven, as doing so may
cause motion sickness.
■
When the system malfunctions
If the symbol shown in the illustra-
tion is displayed when using the
Digital Rearview Mirror in digital mir-
ror mode, the system may be mal-
functioning. The symbol will
disappear in a few seconds. Oper-
ate the lever, change to optical mir-
ror mode and have the vehicle
inspected by your Toyota dealer.
■
Adjusting the mirror height
The height of the rear view mir-
ror can be adjusted to suit your
driving posture.
Change to optical mirror mode,
adjusting the height of the rear
view mirror by moving it up and
down.
■
Display settings (digital mir-
ror mode)
Settings of the display in the dig-
ital mirror mode, on/off operation
of the automatic anti-glare func-
tion, etc. can be changed.
1
Press the menu button.
Adjusting the mirror
170
3-4. Adjusting the steering wheel and mirrors
The icons will be displayed.
2
Press the menu button
repeatedly and select the
item you want to adjust.
3
Press
or
to
change the setting.
The icons will disappear if a button
is not operated for approximately 5
seconds or more.
*
: This is a function for the optical
mirror mode, however, the setting
can also be changed while using
the digital mirror mode.
■
Enabling/disabling the
automatic anti-glare func-
tion (optical mirror mode)
The automatic anti-glare func-
tion in the optical mirror mode
can be enabled/disabled. The
setting can be changed in both
the digital mirror mode and the
optical mirror mode.
When using the digital mirror
mode
When using the optical mirror
mode
1
Press the menu button.
The icons will be displayed.
2
Press the menu button
repeatedly and select
.
Icons
Settings
Select to adjust the bright-
ness of the display.
Select to adjust the area
displayed up/down.
Select to adjust the area
displayed to the left/right.
Select to adjust the angle of
the displayed image.
Select to zoom in/out the
displayed image.
Select to enable/disable the
automatic anti-glare func-
tion.
*
Responding to the bright-
ness of the headlights of
vehicles behind, the
reflected light is automati-
cally adjusted.
The automatic anti-glare
function is enabled each
time the power switch is
changed to ON.
Icons
Settings
171
3-4. Adjusting the steering wheel and mirrors
3
Before driv
ing
The setting display will be dis-
played.
3
Press
or
to
enable (“ON”)/disable
(“OFF”) the automatic
anti-glare function.
The icons will disappear if a button
is not operated for approximately 5
seconds or more.
■
Adjusting the display (digital
mirror mode)
●
If the displayed image is adjusted,
it may appear distorted. This is not
a malfunction.
●
If the brightness of the Digital
Rearview Mirror is set too high, it
may cause eye strain. Adjust the
Digital Rearview Mirror to an
appropriate brightness. If your
eyes become tired, change to
optical mirror mode.
●
The brightness of the Digital Rear-
view Mirror will change automati-
cally according to the brightness
of the area in front of your vehicle.
■
To prevent the light sensors
from malfunctioning
To prevent the light sensors from
malfunctioning, do not touch or
cover them.
WARNING
Observe the following precau-
tions.
Failure to do so may result in
death or serious injury.
■
While driving
●
Do not adjust the position of the
Digital Rearview Mirror or adjust
the display settings while driv-
ing.
Stop the vehicle and operate
the Digital Rearview Mirror con-
trol switches.
Failure to do so may cause a
steering wheel operation error,
resulting in an unexpected acci-
dent.
●
Always pay attention to the
vehicle’s surroundings.
The size of the vehicles and other
objects may look different when in
digital mirror mode and optical
mirror mode.
When backing up, make sure to
directly check the safety of the
area around your vehicle, espe-
cially behind the vehicle.
Additionally, if a vehicle
approaches from the rear in the
dark, such as at night, the sur-
rounding area may appear dim.
■
To prevent causes of fire
If the driver continues using the
Digital Rearview Mirror while
smoke or odor comes from the
mirror, it may result in fire. Stop
using the system immediately and
contact your Toyota dealer.
172
3-4. Adjusting the steering wheel and mirrors
■
Cleaning the mirror surface
If the mirror surface is dirty, the
image on the display may be dif-
ficult to see.
Clean the mirror surface gently
using a soft dry cloth.
■
Cleaning the camera
If the camera lens is dirty or cov-
ered with foreign matter, such as
water droplets, snow, mud, etc.,
the displayed image may not be
clear. In this case, rinse the
camera lens with a large quan-
tity of water and then wipe it
clean with a soft cloth damp-
ened with water.
Dirt on the camera lens can be
cleaned by operating the dedi-
cated camera cleaning washer.
(
■
The camera
The camera for the Digital Rearview
Mirror is located as shown.
Cleaning the Digital Rear-
view Mirror
NOTICE
■
To prevent the Digital Rear-
view Mirror from malfunction-
ing
●
Do not use detergents, such as
thinner, benzine, and alcohol to
clean the mirror. They may dis-
color, deteriorate or damage the
mirror surface.
●
Do not smoke, use matches,
use cigarette lighters or allow
open flames near the mirror. It
may damage the mirror or
cause a fire.
●
Do not remove, disassemble or
modify the mirror.
■
To prevent the camera from
malfunctioning
●
Observe the following precau-
tions, otherwise the Digital
Rearview Mirror may not oper-
ate properly.
• Do not strike or hit the camera
or subject it to a strong impact,
as the camera installation posi-
tion and angle may be changed.
• Do not remove, disassemble or
modify the camera.
• When washing the camera,
rinse it with a large quantity of
water and then wipe it clean
with a soft cloth dampened with
water.
Do not strongly rub the camera
lens, as it may be scratched and
will not be able to transmit a
clear image.
• Do not allow organic solvent,
car wax, window cleaner or
glass coat to adhere to the cam-
era cover. If this happens, wipe
it off as soon as possible.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст