Toyota Corolla Hatchback (2022 year). Manual in english — page 28
455
7-3. Do-it-yourself maintenance
7
Maintena
nce
a
nd ca
re
Under the driver’s side instru-
ment panel
Remove the lid.
Make sure to push the claw when
removing/installing the lid.
3
Remove the fuse with the
pullout tool.
Only type A fuse can be
removed using the pullout
tool.
4
Check if the fuse is blown.
Replace the blown fuse with a new
fuse of an appropriate amperage
rating. The amperage rating can be
found on the fuse box lid.
Type A
Normal fuse
Blown fuse
Type B
Normal fuse
Blown fuse
Type C
Normal fuse
Blown fuse
456
7-3. Do-it-yourself maintenance
Type D
Normal fuse
Blown fuse
Type E
Normal fuse
Blown fuse
■
After a fuse is replaced
●
When installing the lid, make sure
that the tab is installed securely.
●
If the lights do not turn on even
after the fuse has been replaced,
a bulb may need replacement.
●
If the replaced fuse blows again,
have the vehicle inspected by
your Toyota dealer.
■
If there is an overload in a cir-
cuit
The fuses are designed to blow, pro-
tecting the wiring harness from
damage.
■
When replacing light bulbs
Toyota recommends that you use
genuine Toyota products designed
for this vehicle.
Because certain bulbs are con-
nected to circuits designed to pre-
vent overload, non-genuine parts or
parts not designed for this vehicle
may be unusable.
WARNING
■
To prevent system break-
downs and vehicle fire
Observe the following precau-
tions.
Failure to do so may cause dam-
age to the vehicle, and possibly a
fire or injury.
●
Never use a fuse of a higher
amperage rating than that indi-
cated, or use any other object in
place of a fuse.
●
Always use a genuine Toyota
fuse or equivalent.
Never replace a fuse with a
wire, even as a temporary fix.
●
Do not modify the fuses or fuse
boxes.
NOTICE
■
Before replacing fuses
Have the cause of electrical over-
load determined and repaired by
your Toyota dealer as soon as
possible.
457
7-3. Do-it-yourself maintenance
7
Maintena
nce
a
nd ca
re
Check the wattage of the light
bulb to be replaced. (
■
Front
Front side marker lights
■
Rear
License plate lights
■
Bulbs that need to be
replaced by your Toyota
dealer
Headlights
Parking lights
Daytime running lights
Turn signal lights
Front fog lights (if equipped)
Tail lights
Stop lights
Back-up light
High mounted stoplight
■
LED light bulbs
The lights other than the front side
marker lights and license plate lights
consist of a number of LEDs. If any
of the LEDs burn out, take your
vehicle to your Toyota dealer to
have the light replaced.
■
Condensation build-up on the
inside of the lens
Temporary condensation build-up
on the inside of the headlight lens
does not indicate a malfunction.
Contact your Toyota dealer for more
information in the following situa-
tions:
●
Large drops of water have built up
Light bulbs
You may replace the follow-
ing bulbs yourself. The diffi-
culty level of replacement
varies depending on the
bulb. If necessary bulb
replacement seems difficult
to perform, contact your
Toyota dealer.
For more information about
replacing other light bulbs,
contact your Toyota dealer.
Preparing for light bulb
replacement
Bulb locations
458
7-3. Do-it-yourself maintenance
on the inside of the lens.
●
Water has built up inside the
headlight.
■
When replacing light bulbs
■
Front side marker lights
1
Turn the bulb base counter-
clockwise.
2
Remove the light bulb.
3
When installing, reverse the
steps listed.
■
License plate lights
1
Remove the light unit.
Insert a flathead screwdriver or
similar into the hole next to the light
and remove it as shown in the illus-
tration.
To prevent damaging the vehicle,
wrap the flathead screwdriver with
a tape.
2
Turn the bulb base counter-
clockwise and remove it.
3
Remove the light bulb.
4
When installing, reverse the
steps listed.
Replacing light bulbs
459
7-3. Do-it-yourself maintenance
7
Maintena
nce
a
nd ca
re
WARNING
■
Replacing light bulbs
●
Turn off the lights. Do not
attempt to replace the bulb
immediately after turning off the
lights. The bulbs become very
hot and may cause burns.
●
Do not touch the glass portion
of the light bulb with bare
hands. When it is unavoidable
to hold the glass portion, use
and hold with a clean dry cloth
to avoid getting moisture and
oils on the bulb. Also, if the bulb
is scratched or dropped, it may
blow out or crack.
●
Fully install light bulbs and any
parts used to secure them. Fail-
ure to do so may result in heat
damage, fire, or water entering
the light unit. This may damage
the lights or cause condensa-
tion to build up on the lens.
■
To prevent damage or fire
Make sure bulbs are fully seated
and locked.
460
7-3. Do-it-yourself maintenance
461
8
8
Whe
n tr
ouble
ar
ises
When trouble arises
.
8-1. Essential information
Emergency flashers .
If your vehicle has to be
stopped in an emergency
. . . . . . . . ..
If the vehicle is submerged
or water on the road is ris-
ing . . . . . . . .
8-2. Steps to take in an emer-
gency
If your vehicle needs to be
towed. . . . . . .
If you think something is
wrong . . . . . .
Fuel pump shut off system
. . . . . . . . ..
If a warning light turns on or
a warning buzzer sounds
. . . . . . . . ..
If a warning message is dis-
played. . . . . .
If you have a flat tire (vehi-
cles without spare tire)
. . . . . . . . ..
If you have a flat tire (vehi-
cles with a spare tire)
. . . . . . . . ..
If the engine will not start
. . . . . . . . ..
If you lose your keys ...
If the electronic key does
not operate properly ..
If the vehicle battery is dis-
charged . . . . . .
If your vehicle overheats
. . . . . . . . ..
If the vehicle becomes stuck
. . . . . . . . ..
462
8-1. Essential information
8-1.Essential information
Press the switch.
All the turn signal lights will flash.
To turn them off, press the switch
once again.
■
Emergency flashers
●
If the emergency flashers are
used for a long time while the
engine is not operating, the bat-
tery may discharge.
●
If any of the SRS airbags deploy
(inflate) or in the event of a strong
rear impact, the emergency flash-
ers will turn on automatically.
The emergency flashers will turn
off automatically after operating
for approximately 20 minutes. To
manually turn the emergency
flashers off, press the switch
twice.
(The emergency flashers may not
turn on automatically depending
on the force of the impact and
conditions of the collision.)
1
Steadily step on the brake
pedal with both feet and
firmly depress it.
Do not pump the brake pedal
repeatedly as this will increase the
effort required to slow the vehicle.
2
Shift the shift lever to N.
If the shift lever is shifted to N
3
After slowing down, stop the
vehicle in a safe place by the
road.
4
Stop the engine.
If the shift lever cannot be
shifted to N
3
Keep depressing the brake
pedal with both feet to reduce
vehicle speed as much as
possible.
4
To stop the engine, press and
hold the engine switch for 2
consecutive seconds or
Emergency flashers
The emergency flashers are
used to warn other drivers
when the vehicle has to be
stopped on the road due to
a breakdown, etc.
Operating instructions
If your vehicle has to
be stopped in an emer-
gency
Only in an emergency, such
as if it becomes impossible
to stop the vehicle in the
normal way, stop the vehicle
using the following proce-
dure:
Stopping the vehicle
463
8-1. Essential information
8
W
he
n
tro
ub
le
ar
is
es
more, or press it briefly 3
times or more in succession.
5
Stop the vehicle in a safe
place by the road.
If the door can be opened,
open the door and exit the
vehicle.
If the door can not be opened,
open the window using the
power window switch and
ensure an escape route.
If the window can be opened,
exit the vehicle through the
window.
If the door and window cannot
be opened due to the rising
water, remain calm, wait until
the water level inside the
vehicle rises to the point that
the water pressure inside of
the vehicle equals the water
pressure outside of the vehi-
cle and then open the door
after waiting for the rising
water to enter the vehicle, and
exit the vehicle. When the
WARNING
■
If the engine has to be turned
off while driving
Power assist for the brakes and
steering wheel will be lost, making
the brake pedal harder to depress
and the steering wheel heavier to
turn. Decelerate as much as pos-
sible before turning off the engine.
If the vehicle is sub-
merged or water on
the road is rising
This vehicle is not designed
to be able to drive on roads
that are deeply flooded with
water. Do not drive on roads
where the roads may be
submerged or the water
may be rising. It is danger-
ous to remain in the vehicle,
if it anticipated that the vehi-
cle will be flooded or set a
drift. Remain calm and fol-
low the following.
464
8-1. Essential information
outside water level exceeds
half the height of the door, the
door cannot be opened from
the inside due to water pres-
sure.
■
Water level exceeds the floor
When the water level exceeds the
floor and time has passed, the elec-
trical equipment will get damaged,
the power windows will not operate,
the engine stop, and the vehicle
may not be able to get moving.
■
Using an emergency escape
hammer
*
Laminated glass is used in the wind-
shield on this vehicle.
Laminated glass cannot be shat-
tered with an emergency hammer
*
.
Tempered glass is used in the win-
dows on this vehicle.
*
: Contact your Toyota dealer or
aftermarket accessory manufac-
turer for further information about
an emergency hammer.
WARNING
■
Caution while driving
Do not drive on roads where the
roads may be submerged or the
water may be rising. Otherwise
the vehicle may be damaged and
cannot move, as well as become
flooded and set a drift, which may
lead to death.
465
8-2. Steps to take in an emergency
8
W
he
n
tro
ub
le
ar
is
es
8-2.Steps to take in an emergency
If your vehicle needs
to be towed
If towing is necessary, we
recommend having your
vehicle towed by your Toy-
ota dealer or commercial
towing service, using a
wheel-lift type truck or flat-
bed truck.
Use a safety chain system
for all towing, and abide by
all state/provincial and local
laws.
WARNING
Observe the following precau-
tions.
Failure to do so may result in
death or serious injury.
■
When towing the vehicle
Be sure to transport the vehicle
with the front wheels raised or
with all four wheels raised off the
ground. If the vehicle is towed
with the front wheels contacting
the ground, the drivetrain and
related parts may be damaged.
■
While towing
●
When towing using cables or
chains, avoid sudden starts, etc.
which place excessive stress on
the towing eyelets, cables or
chains. The towing eyelets,
cables or chains may become
damaged, broken debris may hit
people, and cause serious dam-
age.
●
Do not turn the engine switch
off.
There is a possibility that the
steering wheel is locked and
cannot be operated.
■
Installing towing eyelets to
the vehicle
Make sure that towing eyelets are
installed securely.
If not securely installed, towing
eyelets may come loose during
towing.
NOTICE
■
To prevent damage to the
vehicle when towing using a
wheel-lift type truck
●
Do not tow the vehicle from the
rear when the engine switch is
off. The steering lock mecha-
nism is not strong enough to
hold the front wheels straight.
●
When raising the vehicle,
ensure adequate ground clear-
ance for towing at the opposite
end of the raised vehicle. With-
out adequate clearance, the
vehicle could be damaged while
being towed.
■
To prevent damage to the
vehicle when towing with a
sling-type truck
Do not tow with a sling-type truck,
either from the front or rear.
466
8-2. Steps to take in an emergency
The following may indicate a
problem with your transmission.
Contact your Toyota dealer or
commercial towing service
before towing.
The engine is running but the
vehicle does not move.
The vehicle makes an abnor-
mal sound.
From the front
Release the parking brake.
Turn automatic mode off.
(
From the rear
Use a towing dolly under the
front wheels.
When using a flat-bed truck to
transport the vehicle, use tire
strapping belts. Refer to the
owner's manual of the flat-bed
truck for the tire strapping
method.
In order to suppress vehicle
movement during transporta-
tion, set the parking brake and
turn the engine switch off.
If a tow truck is not available in
NOTICE
■
To prevent damage to the
vehicle during emergency
towing
Do not secure cables or chains to
the suspension components.
Situations when it is nec-
essary to contact dealers
before towing
Towing with a wheel-lift
type truck
NOTICE
■
Towing with a sling-type truck
Do not tow with a sling-type truck
to prevent body damage.
Using a flatbed truck
Emergency towing
467
8-2. Steps to take in an emergency
8
Whe
n tr
ouble
ar
ises
an emergency, your vehicle may
be temporarily towed using
cables or chains secured to the
emergency towing eyelets. This
should only be attempted on
hard surfaced roads for at most
50 miles (80 km) at under 18
mph (30 km/h).
A driver must be in the vehicle to
steer and operate the brakes.
The vehicle’s wheels, drive train,
axles, steering and brakes must
be in good condition.
For vehicles with a continuously
variable transmission, only the
front towing eyelets may be
used.
To have your vehicle towed by
another vehicle, the towing eye-
let must be installed to your
vehicle. Install the towing eyelet
using the following procedure.
1
Take out the wheel nut
wrench, flathead screwdriver
and towing eyelet. (
2
Remove the eyelet cover
using a flathead screwdriver.
To protect the bodywork, place a
rag between the screwdriver and
the vehicle body as shown in the
illustration.
3
Insert the towing eyelet into
the hole and tighten partially
by hand.
4
Tighten down the towing eye-
let securely using a wheel nut
wrench or hard metal bar.
5
Securely attach cables or
chains to the towing eyelet.
Take care not to damage the vehi-
Emergency towing proce-
dure
468
8-2. Steps to take in an emergency
cle body.
6
Enter the vehicle being towed
and start the engine.
If the engine does not start, turn the
engine switch to ON.
7
Shift the shift lever to N and
release the parking brake.
Turn automatic mode off.
(
Vehicles with a continuously
variable transmission: When
the shift lever cannot be
shifted:
■
While towing
If the engine is not running, the
power assist for the brakes and
steering will not function, making
steering and braking more difficult.
■
Wheel nut wrench
Wheel nut wrench is installed in lug-
gage compartment. (
Fluid leaks under the vehicle.
(Water dripping from the air
conditioning after use is nor-
mal.)
Flat-looking tires or uneven
tire wear
Engine coolant temperature
gauge needle continually
points higher than normal.
Changes in exhaust sound
Excessive tire squeal when
cornering
Strange noises related to the
suspension system
Pinging or other noises
related to the engine
Engine missing, stumbling or
running roughly
Appreciable loss of power
Vehicle pulls heavily to one
If you think something
is wrong
If you notice any of the fol-
lowing symptoms, your
vehicle probably needs
adjustment or repair. Con-
tact your Toyota dealer as
soon as possible.
Visible symptoms
Audible symptoms
Operational symptoms
469
8-2. Steps to take in an emergency
8
W
he
n
tro
ub
le
ar
is
es
side when braking
Vehicle pulls heavily to one
side when driving on a level
road
Loss of brake effectiveness,
spongy feeling, pedal almost
touches the floor
Follow the procedure below to
restart the engine after the sys-
tem is activated.
1
Turn the engine switch to
ACC or OFF.
2
Restart the engine.
Fuel pump shut off
system
To minimize the risk of fuel
leakage when the engine
stalls or when an airbag
inflates upon collision, the
fuel pump shut off system
stops the supply of fuel to
the engine.
Restarting the engine
NOTICE
■
Before starting the engine
Inspect the ground under the
vehicle.
If you find that fuel has leaked
onto the ground, the fuel system
has been damaged and is in need
of repair. Do not restart the
engine.
470
8-2. Steps to take in an emergency
■
Brake system warning light (warning buzzer)
■
Brake system warning light
■
High coolant temperature warning light
*
(warning buzzer)
*
: This light illuminates on the multi-information display.
If a warning light turns on or a warning buzzer
sounds
Calmly perform the following actions if any of the warning
lights comes on or flashes. If a light comes on or flashes, but
then goes off, this does not necessarily indicate a malfunction
in the system. However, if this continues to occur, have the
vehicle inspected by your Toyota dealer.
Actions to the warning lights or warning buzzers
Warning light
Details/Actions
(U.S.A.)
or
(Red)
(Canada)
Indicates that:
The brake fluid level is low; or
The brake system is malfunctioning
Immediately stop the vehicle in a safe place and con-
tact your Toyota dealer. Continuing to drive the vehi-
cle may be dangerous.
Warning light
Details/Actions
(Yellow)
Indicates a malfunction in the parking brake system
Have the vehicle inspected by your Toyota dealer
immediately.
Warning light
Details/Actions
Indicates that the engine coolant temperature is exces-
sively high
Immediately stop the vehicle in a safe place.
Handling method (
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст