Toyota Corolla Hatchback (2022 year). Manual in english — page 13
208
4-5. Using the driving support systems
1
With the cruise control off,
press and hold the cruise
control main switch for 1.5
seconds or more.
Immediately after the switch is
pressed, the dynamic radar cruise
control indicator will come on. After-
wards, it switches to the cruise con-
trol indicator.
Switching to constant speed control
mode is only possible when operat-
ing the switch with the cruise con-
trol off.
2
Accelerate or decelerate,
with accelerator pedal opera-
tion, to the desired vehicle
speed (at or above approxi-
mately 20 mph [30 km/h])
and press the “-SET” switch
to set the speed.
Cruise control “SET” indicator will
come on.
The vehicle speed at the moment
the switch is released becomes the
set speed.
Adjusting the speed setting:
Canceling and resuming the speed
setting:
■
Dynamic radar cruise control
with full-speed range can be set
when
●
The shift lever is in D.
●
The desired set speed can be set
when the vehicle speed is approx-
imately 20 mph (30 km/h) or more.
(However, when the vehicle speed
is set while driving at below
approximately 20 mph [30 km/h],
the set speed will be set to
approximately 20 mph [30 km/h].)
■
Accelerating after setting the
vehicle speed
The vehicle can accelerate by oper-
ating the accelerator pedal. After
accelerating, the set speed
resumes. However, during vehi-
cle-to-vehicle distance control
mode, the vehicle speed may
decrease below the set speed in
order to maintain the distance to the
preceding vehicle.
■
When the vehicle stops while
follow-up cruising
●
Pressing the “+RES” switch while
the vehicle ahead stops will
resume follow-up cruising if the
vehicle ahead starts off within
approximately 3 seconds after the
switch is pressed.
●
If the vehicle ahead starts off
within 3 seconds after your vehicle
stops, follow-up cruising will be
resumed.
209
4-5. Using the driving support systems
4
Dr
iv
ing
■
Automatic cancelation of vehi-
cle-to-vehicle distance control
mode
Vehicle-to-vehicle distance control
mode is automatically canceled in
the following situations.
●
VSC is activated.
●
TRAC is activated for a period of
time.
●
When the VSC or TRAC system is
turned off.
●
The sensor cannot detect cor-
rectly because it is covered in
some way.
●
When the brake control or output
restriction control of a driving sup-
port system operates.(For exam-
ple: Pre-Collision System,
Drive-Start Control)
●
The parking brake is operated.
●
The vehicle is stopped by system
control on a steep incline.
●
The following are detected when
the vehicle has been stopped by
system control:
• The driver is not wearing a seat
belt.
• The driver’s door is opened.
• The vehicle has been stopped for
about 3 minutes
If vehicle-to-vehicle distance control
mode is automatically canceled for
any reasons other than the above,
there may be a malfunction in the
system. Contact your Toyota dealer.
■
Automatic cancelation of con-
stant speed control mode
Constant speed control mode is
automatically canceled in the follow-
ing situations:
●
Actual vehicle speed is more than
approximately 10 mph (16 km/h)
below the set vehicle speed.
●
Actual vehicle speed falls below
approximately 20 mph (30 km/h).
●
VSC is activated.
●
TRAC is activated for a period of
time.
●
When the VSC or TRAC system is
turned off.
●
When the brake control or output
restriction control of a driving sup-
port system operates.(For exam-
ple: Pre-Collision System,
Drive-Start Control)
If constant speed control mode is
automatically canceled for any rea-
sons other than the above, there
may be a malfunction in the system.
Contact your Toyota dealer.
■
Brake operation
A brake operation sound may be
heard and the brake pedal response
may change, but these are not mal-
functions.
■
Warning messages and buzzers
for dynamic radar cruise con-
trol with full-speed range
Warning messages and buzzers are
used to indicate a system malfunc-
tion or to inform the driver of the
need for caution while driving. If a
warning message is shown on the
multi-information display, read the
message and follow the instructions.
(
■
When the sensor may not be
correctly detecting the vehicle
ahead
In the case of the following and
depending on the conditions, oper-
ate the brake pedal when decelera-
tion of the system is insufficient or
operate the accelerator pedal when
acceleration is required.
As the sensor may not be able to
correctly detect these types of vehi-
cles, the approach warning
(
P.207) may not be activated.
●
Vehicles that cut in suddenly
●
Vehicles traveling at low speeds
●
Vehicles that are not moving in the
same lane
●
Vehicles with small rear ends
(trailers with no load on board,
210
4-5. Using the driving support systems
etc.)
●
Motorcycles traveling in the same
lane
●
When water or snow thrown up by
the surrounding vehicles hinders
the detecting of the sensor
●
When your vehicle is pointing
upwards (caused by a heavy load
in the luggage compartment, etc.)
●
Preceding vehicle has an
extremely high ground clearance
■
Conditions under which the
vehicle-to-vehicle distance con-
trol mode may not function cor-
rectly
In the case of the following condi-
tions, operate the brake pedal (or
accelerator pedal, depending on the
situation) as necessary.
As the sensor may not be able to
correctly detect vehicles ahead, the
system may not operate properly.
●
When the road curves or when the
lanes are narrow
●
When steering wheel operation or
your position in the lane is unsta-
ble
●
When the vehicle ahead of you
decelerates suddenly
●
When driving on a road sur-
rounded by a structure, such as in
a tunnel or on a bridge
●
While the vehicle speed is
decreasing to the set speed after
the vehicle accelerates by
depressing the accelerator pedal
211
4-5. Using the driving support systems
4
Dr
iv
ing
*
: If equipped
■
Meter display
Multi-information display
Set speed
Indicators
■
Operation switches
Vehicle-to-vehicle distance
switch
“+RES” switch
Cruise control main switch
Cancel switch
“-SET” switch
Dynamic radar cruise
control
*
In vehicle-to-vehicle dis-
tance control mode, the
vehicle automatically accel-
erates and decelerates to
match the speed changes of
the preceding vehicle even
if the accelerator pedal is
not depressed. In constant
speed control mode, the
vehicle runs at a fixed
speed.
Use the dynamic radar
cruise control on freeways
and highways.
Vehicle-to-vehicle distance
control mode (
Constant speed control
mode (
System Components
WARNING
■
Before using dynamic radar
cruise control
●
Driving safely is the sole
responsibility of the driver. Do
not rely solely on the system,
and drive safely by always pay-
ing careful attention to your sur-
roundings.
●
The dynamic radar cruise con-
trol provides driving assistance
to reduce the driver’s burden.
However, there are limitations to
the assistance provided.
Read the following conditions
carefully. Do not overly rely on
this system and always drive
carefully.
• When the sensor may not be
correctly detecting the vehicle
ahead:
• Conditions under which the
vehicle-to-vehicle distance con-
trol mode may not function cor-
rectly:
212
4-5. Using the driving support systems
WARNING
●
Set the speed appropriately
depending on the speed limit,
traffic flow, road conditions,
weather conditions, etc. The
driver is responsible for check-
ing the set speed.
●
Even when the system is func-
tioning normally, the condition of
the preceding vehicle as
detected by the system may dif-
fer from the condition observed
by the driver. Therefore, the
driver must always remain alert,
assess the danger of each situ-
ation and drive safely. Relying
solely on this system or assum-
ing the system ensures safety
while driving can lead to an
accident, resulting in death or
serious injury.
●
Switch the dynamic radar cruise
control setting to off, using the
cruise control main switch when
not in use.
■
Cautions regarding the driv-
ing assist systems
Observe the following precau-
tions, as there are limitations to
the assistance provided by the
system.
Failure to do so may cause an
accident resulting in death or seri-
ous injury.
●
Assisting the driver to measure
following distance
The dynamic radar cruise control
is only intended to help the driver
in determining the following dis-
tance between the driver’s own
vehicle and a designated vehicle
traveling ahead. It is not a mecha-
nism that allows careless or inat-
tentive driving, and it is not a
system that can assist the driver
in low-visibility conditions.
It is still necessary for driver to
pay close attention to the vehi-
cle’s surroundings.
●
Assisting the driver to judge
proper following distance
The dynamic radar cruise control
determines whether the following
distance between the driver’s own
vehicle and a designated vehicle
traveling ahead is within a set
range. It is not capable of making
any other type of judgement.
Therefore, it is absolutely neces-
sary for the driver to remain vigi-
lant and to determine whether or
not there is a possibility of danger
in any given situation.
●
Assisting the driver to operate
the vehicle
The dynamic radar cruise control
does not include functions which
will prevent or avoid collisions
with vehicles ahead of your vehi-
cle. Therefore, if there is ever any
possibility of danger, the driver
must take immediate and direct
control of the vehicle and act
appropriately in order to ensure
the safety of all involved.
213
4-5. Using the driving support systems
4
Dr
iv
ing
WARNING
■
Situations unsuitable for
dynamic radar cruise control
Do not use dynamic radar cruise
control in any of the following situ-
ations.
Doing so may result in inappropri-
ate speed control and could
cause an accident resulting in
death or serious injury.
●
Roads where there are pedes-
trians, cyclists, etc.
●
In heavy traffic
●
On roads with sharp bends
●
On winding roads
●
On slippery roads, such as
those covered with rain, ice or
snow
●
On steep downhills, or where
there are sudden changes
between sharp up and down
gradients
Vehicle speed may exceed the
set speed when driving down a
steep hill.
●
At entrances to freeways and
highways
●
When weather conditions are
bad enough that they may pre-
vent the sensors from detecting
correctly (fog, snow, sand-
storm, heavy rain, etc.)
●
When there is rain, snow, etc.
on the front surface of the radar
or front camera
●
In traffic conditions that require
frequent repeated acceleration
and deceleration
●
During emergency towing
●
When an approach warning
buzzer is heard often
214
4-5. Using the driving support systems
This mode employs a radar to detect the presence of vehicles up to
approximately 328 ft. (100 m) ahead, determines the current vehi-
cle-to-vehicle following distance, and operates to maintain a suitable
following distance from the vehicle ahead. The desired vehi-
cle-to-vehicle distance can also be set by operating the vehi-
cle-to-vehicle distance switch.
When driving on downhill slopes, the vehicle-to-vehicle distance may
become shorter.
Example of constant speed cruising
When there are no vehicles ahead
The vehicle travels at the speed set by the driver.
Example of deceleration cruising and follow-up cruising
When a preceding vehicle driving slower than the set speed
appears
When a vehicle is detected running ahead of you, the system automatically
decelerates your vehicle. When a greater reduction in vehicle speed is nec-
essary, the system applies the brakes (the stop lights will come on at this
time). The system will respond to changes in the speed of the vehicle
ahead in order to maintain the vehicle-to-vehicle distance set by the driver.
Approach warning warns you when the system cannot decelerate suffi-
ciently to prevent your vehicle from closing in on the vehicle ahead.
When the turn signal lever is operated and your vehicle moves to an over-
taking lane while driving at 50 mph (80 km/h) or more, the vehicle will accel-
erate to help to overtake a passing vehicle.
The system’s identification of what is an overtaking lane may be determined
solely based on the location of the steering wheel in the vehicle (left side
Driving in vehicle-to-vehicle distance control mode
215
4-5. Using the driving support systems
4
Dr
iv
ing
driver position versus right side driver position.) If the vehicle is driven to a
region where the overtaking lane is on a different side from where the vehi-
cle is normally driven, the vehicle may accelerate when the turn signal lever
is operated in the opposite direction to the overtaking lane (e.g., if the driver
normally operates the vehicle in a region where the overtaking lane is to the
right but then drives to a region where the overtaking lane is to the left, the
vehicle may accelerate when the right turn signal is activated).
Example of acceleration
When there are no longer any preceding vehicles driving slower
than the set speed
The system accelerates until the set speed is reached. The system then
returns to constant speed cruising.
1
Press the cruise control main
switch to activate the cruise
control.
Dynamic radar cruise control indi-
cator will come on and a message
will be displayed on the multi-infor-
mation display. Press the switch
again to deactivate the cruise con-
trol.
If the cruise control main switch is
pressed and held for 1.5 seconds
or more, the system turns on in
constant speed control mode.
(
2
Accelerate or decelerate,
with accelerator pedal opera-
tion, to the desired vehicle
speed (at or above approxi-
mately 20 mph [30 km/h])
and press the “-SET” switch
to set the speed.
Cruise control “SET” indicator will
come on.
The vehicle speed at the moment
the switch is released becomes the
set speed.
To change the set speed, press
the “+RES” or “-SET” switch
until the desired set speed is
displayed.
Setting the vehicle speed
(vehicle-to-vehicle dis-
tance control mode)
Adjusting the set speed
216
4-5. Using the driving support systems
1
Increases the speed
2
Decreases the speed
Fine adjustment: Press the switch.
Large adjustment: Press and hold
the switch to change the speed,
and release when the desired
speed is reached.
In the vehicle-to-vehicle dis-
tance control mode, the set
speed will be increased or
decreased as follows:
For the U.S. mainland, Hawaii
Fine adjustment: By 1 mph (1.6
km/h)
*1
or 1 km/h (0.6 mph)
*2
each
time the switch is pressed
Large adjustment: Increases or
decreases in 1 mph (1.6 km/h)
*1
or
1 km/h (0.6 mph)
*2
increments for
as long as the switch is held
For Canada, Guam and
Puerto Rico
Fine adjustment: By 1 mph (1.6
km/h)
*1
or 1 km/h (0.6 mph)
*2
each
time the switch is pressed
Large adjustment: Increases or
decreases in 5 mph (8 km/h)
*1
or 5
km/h (3.1 mph)
*2
increments for as
long as the switch is held
In the constant speed control
mode (
P.218), the set speed
will be increased or decreased
as follows:
Fine adjustment: By 1 mph (1.6
km/h)
*1
or 1 km/h (0.6 mph)
*2
each
time the switch is pressed
Large adjustment: The speed will
continue to change while the switch
is held.
*1
:When the set speed is shown in
“MPH”
*2
:When the set speed is shown in
“km/h”
Pressing the switch changes the
vehicle-to-vehicle distance as
follows:
1
Long
2
Medium
3
Short
If a vehicle is running ahead of you,
the preceding vehicle mark
will
also be displayed.
Changing the vehi-
cle-to-vehicle distance
(vehicle-to-vehicle dis-
tance control mode)
217
4-5. Using the driving support systems
4
Dr
iv
ing
Select a distance from the table
below. Note that the distances
shown correspond to a vehicle
speed of 50 mph (80 km/h).
Vehicle-to-vehicle distance
increases/decreases in accor-
dance with vehicle speed.
1
Pressing the cancel switch
cancels the speed control.
The speed control is also canceled
when the brake pedal is depressed.
2
Pressing the “+RES” switch
resumes the cruise control
and returns vehicle speed to
the set speed.
However, cruise control does not
resume when the vehicle speed is
approximately 16 mph (25 km/h) or
less.
When your vehicle is too close
to a vehicle ahead, and suffi-
cient automatic deceleration via
the cruise control is not possi-
ble, the display will flash and the
buzzer will sound to alert the
driver. An example of this would
be if another driver cuts in front
of you while you are following a
vehicle. Depress the brake
pedal to ensure an appropriate
vehicle-to-vehicle distance.
■
Warnings may not occur
when
In the following instances, warn-
ings may not occur even when
the vehicle-to-vehicle distance is
small.
When the speed of the pre-
ceding vehicle matches or
Vehicle-to-vehicle dis-
tance settings (vehi-
cle-to-vehicle distance
control mode)
Distance
options
Vehicle-to-vehicle dis-
tance
Long
Approximately 160 ft.
(50 m)
Medium
Approximately 130 ft.
(40 m)
Short
Approximately 100 ft.
(30 m)
Canceling and resuming
the speed control
Approach warning (vehi-
cle-to-vehicle distance
control mode)
218
4-5. Using the driving support systems
exceeds your vehicle speed
When the preceding vehicle is
traveling at an extremely slow
speed
Immediately after the cruise
control speed was set
When depressing the acceler-
ator pedal
When constant speed control
mode is selected, your vehicle
will maintain a set speed without
controlling the vehicle-to-vehi-
cle distance. Select this mode
only when vehicle-to-vehicle dis-
tance control mode does not
function correctly due to a dirty
radar, etc.
1
With the cruise control off,
press and hold the cruise
control main switch for 1.5
seconds or more.
Immediately after the switch is
pressed, the dynamic radar cruise
control indicator will come on. After-
wards, it switches to the cruise con-
trol indicator.
Switching to constant speed control
mode is only possible when operat-
ing the switch with the cruise con-
trol off.
2
Accelerate or decelerate,
with accelerator pedal opera-
tion, to the desired vehicle
speed (at or above approxi-
mately 20 mph [30 km/h])
and press the “-SET” switch
to set the speed.
Cruise control “SET” indicator will
come on.
The vehicle speed at the moment
the switch is released becomes the
set speed.
Adjusting the speed setting:
Canceling and resuming the speed
setting:
■
Dynamic radar cruise control
can be set when
●
The shift lever is in range 2nd or
higher.
●
Depending on the control mode,
this item can be set at the follow-
ing speeds.
Selecting constant speed
control mode
219
4-5. Using the driving support systems
4
Dr
iv
ing
• Vehicle-to-vehicle distance con-
trol mode: Approximately 20 mph
(30 km/h) or more
• Constant speed control mode:
Approximately 20 mph (30 km/h)
or more
■
Accelerating after setting the
vehicle speed
The vehicle can accelerate by oper-
ating the accelerator pedal. After
accelerating, the set speed
resumes. However, during vehi-
cle-to-vehicle distance control
mode, the vehicle speed may
decrease below the set speed in
order to maintain the distance to the
preceding vehicle.
■
Shift position selection
Select a shift position according to
the vehicle speed. If the engine
speed is too high or too low, control
may be automatically canceled.
■
Automatic cancelation of vehi-
cle-to-vehicle distance control
mode
Vehicle-to-vehicle distance control
mode is automatically canceled in
the following situations.
●
Actual vehicle speed falls below
approximately 16 mph (25 km/h).
●
VSC is activated.
●
TRAC is activated for a period of
time.
●
When the VSC or TRAC system is
turned off.
●
The sensor cannot detect cor-
rectly because it is covered in
some way.
●
When the brake control or output
restriction control of a driving sup-
port system operates.(For exam-
ple: Pre-Collision System,
Drive-Start Control)
●
When the shift lever is in N or the
clutch pedal is depressed for a
certain amount of time or more.
If vehicle-to-vehicle distance control
mode is automatically canceled for
any reasons other than the above,
there may be a malfunction in the
system. Contact your Toyota dealer.
■
Automatic cancelation of con-
stant speed control mode
Constant speed control mode is
automatically canceled in the follow-
ing situations:
●
Actual vehicle speed is more than
approximately 10 mph (16 km/h)
below the set vehicle speed.
●
Actual vehicle speed falls below
approximately 20 mph (30 km/h).
●
VSC is activated.
●
TRAC is activated for a period of
time.
●
When the VSC or TRAC system is
turned off.
●
When the brake control or output
restriction control of a driving sup-
port system operates.(For exam-
ple: Pre-Collision System,
Drive-Start Control)
●
When the shift lever is in N or the
clutch pedal is depressed for a
certain amount of time or more.
If constant speed control mode is
automatically canceled for any rea-
sons other than the above, there
may be a malfunction in the system.
Contact your Toyota dealer.
■
Brake operation
A brake operation sound may be
heard and the brake pedal response
may change, but these are not mal-
functions.
■
Warning messages and buzzers
for dynamic radar cruise con-
trol
Warning messages and buzzers are
used to indicate a system malfunc-
tion or to inform the driver of the
need for caution while driving. If a
warning message is shown on the
multi-information display, read the
message and follow the instructions.
(
220
4-5. Using the driving support systems
■
When the sensor may not be
correctly detecting the vehicle
ahead
In the case of the following and
depending on the conditions, oper-
ate the brake pedal when decelera-
tion of the system is insufficient or
operate the accelerator pedal when
acceleration is required.
As the sensor may not be able to
correctly detect these types of vehi-
cles, the approach warning
(
P.217) may not be activated.
●
Vehicles that cut in suddenly
●
Vehicles traveling at low speeds
●
Vehicles that are not moving in the
same lane
●
Vehicles with small rear ends
(trailers with no load on board,
etc.)
●
Motorcycles traveling in the same
lane
●
When water or snow thrown up by
the surrounding vehicles hinders
the detecting of the sensor
●
When your vehicle is pointing
upwards (caused by a heavy load
in the luggage compartment, etc.)
●
Preceding vehicle has an
extremely high ground clearance
■
Conditions under which the
vehicle-to-vehicle distance con-
trol mode may not function cor-
rectly
In the case of the following condi-
tions, operate the brake pedal (or
accelerator pedal, depending on the
situation) as necessary.
As the sensor may not be able to
correctly detect vehicles ahead, the
system may not operate properly.
●
When the road curves or when the
lanes are narrow
●
When steering wheel operation or
your position in the lane is unsta-
ble
●
When the vehicle ahead of you
decelerates suddenly
●
When driving on a road sur-
rounded by a structure, such as in
a tunnel or on a bridge
●
While the vehicle speed is
decreasing to the set speed after
the vehicle accelerates by
221
4-5. Using the driving support systems
4
Dr
iv
ing
depressing the accelerator pedal
*
: If equipped
RSA (Road Sign
Assist)
*
The RSA system recognizes
specific road signs using
the front camera to provide
information to the driver via
the display.
If the system judges that the
vehicle is being driven over
the speed limit, performing
prohibited actions, etc.
according to the recog-
nized road signs, it notifies
the driver through a visual
notification and notification
buzzer .
WARNING
■
Before using the RSA
Do not rely solely upon the RSA
system. RSA is a system which
supports the driver by providing
information, but it is not a replace-
ment for a driver’s own vision and
awareness. Drive safely by
always paying careful attention to
the traffic rules.
222
4-5. Using the driving support systems
When the front camera recog-
nizes a sign, the sign will be dis-
played on the multi-information
display.
• Speed limit sign
When the driving support sys-
tem information is selected, a
maximum of 3 signs can be
displayed. (
When a tab other than the
driving support system infor-
mation is selected, the follow-
ing types of road signs will be
displayed. (
P.82)
• Speed limit sign
• Do Not Enter sign (when notifica-
tion is necessary)
If signs other than speed limit signs
are recognized, they will be dis-
played in an overlapping stack
under the current speed limit sign.
The following types of road
signs, including electronic signs
and blinking signs, are dis-
played.
A non-official or a recently intro-
duced traffic sign may not be dis-
played.
Speed limit
Do Not Enter
Stop
Yield
In the following situations, the
RSA system will notify the
driver.
When the vehicle speed
exceeds the speed notifica-
tion threshold of the speed
limit sign displayed, the sign
display will be emphasized
and a buzzer will sound.
Indication on the
multi-information display
Supported types of road
signs
Notification function
223
4-5. Using the driving support systems
4
Dr
iv
ing
When the RSA system recog-
nizes a do not enter sign and
determines that your vehicle
has entered a no-entry area,
the displayed sign will flash
and a buzzer will sound.
Depending on the situation, a
notification function may not
operate properly.
■
Setting procedure
1
Press
or
of the meter
control switches and select
2
Press
or
of the meter
control switches and select
, then press
■
Automatic turn-off of RSA sign
display
In the following situations, a dis-
played speed limit sign and/or do
not enter sign will stop being dis-
played automatically:
●
No sign has been recognized for a
certain distance.
●
The road changes due to a left or
right turn, etc.
In the following situations, stop and
yield signs will stop being displayed
automatically:
●
The system determines that your
vehicle has passed the sign.
●
The road changes due to a left or
right turn, etc.
■
Conditions in which the func-
tion may not operate or detect
correctly
In the following situations, RSA
does not operate normally and may
not recognize signs, display the
incorrect sign, etc. However, this
does not indicate a malfunction.
●
The front camera is misaligned
due to a strong impact being
applied to the sensor, etc.
●
Dirt, snow, stickers, etc. are on the
windshield near the front camera.
●
In inclement weather such as
heavy rain, fog, snow or sand
storms
●
Light from an oncoming vehicle,
the sun, etc. enters the front cam-
era.
●
The sign is dirty, faded, tilted or
bent.
●
The contrast of electronic sign is
low.
●
All or part of the sign is hidden by
the leaves of a tree, a pole, etc.
●
The sign is only visible to the front
camera for a short amount of time.
●
The driving scene (turning, lane
change, etc.) is judged incorrectly.
●
If a sign not appropriate for the
currently traveled lane, but the
sign exists directly after a freeway
branches, or in an adjacent lane
just before merging.
●
Stickers are attached to the rear of
the preceding vehicle.
●
A sign resembling a system com-
patible sign is recognized.
●
Side road speed signs may be
detected and displayed (if posi-
tioned in sight of the front camera)
while the vehicle is traveling on
the main road.
●
Roundabout exit road speed signs
may be detected and displayed (if
positioned in sight of the front
camera) while traveling on a
roundabout.
●
The front of the vehicle is raised or
lowered due to the carried load.
●
The surrounding brightness is not
sufficient or changes suddenly.
●
When a sign intended for trucks,
etc. is recognized.
●
The speed information displayed
on the meter and on the naviga-
tion system may be different due
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст