Toyota Tundra (2015 year). Manual — part 529
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000004M6X017X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION FLUID: REPLACEMENT; 2015 MY
Tundra [08/2014 - ]
REPLACEMENT
1. REPLACE AUTOMATIC TRANSMISSION FLUID
(a) Lift the vehicle. [*1]
NOTICE:
Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle
(c) Temporarily install the gasket and drain plug. [*3]
HINT:
Reuse the old gasket. A new gasket will be installed in step. [*15]
(d) Remove the refill plug and overflow plug. [*4]
NOTICE:
Use Toyota Genuine ATF WS.
(f) Wait until the fluid flow slows and only drops come out. [*6]
(g) Temporarily install the gasket and overflow plug. [*7]
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
HINT:
Reuse the old gasket. The plug will be removed again to adjust the fluid level.
HINT:
HINT:
Reuse the old gasket. The plug will be removed again to adjust the fluid level.
(j) Lower the vehicle. [*10]
(k) Start the engine. [*11]
NOTICE:
Make sure that the A/C switch is off.
(l) Slowly move the shift lever from P to S, then change the gear from 1st to 6th. Then return the shift lever
to P. [*12]
(m) Allow the engine to idle for 30 seconds to warm it up. [*13]
(n) Turn the ignition switch off. [*14]
(o) Repeat steps [*1] to [*14].
(p) Repeat steps [*1] to [*2].
(q) Install a new gasket and the drain plug. [*15]
Torque:
20 N·m {204 kgf·cm, 15ft·lbf}
(r) Repeat steps [*4] to [*10].
(s) Adjust the fluid level
.
(t) Lower the vehicle.
(u) Operation complete.
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Last Modified: 9-16-2014
6.6 N
Doc ID: RM000002BL004OX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION FLUID: ADJUSTMENT; 2015 MY Tundra
[08/2014 - ]
ADJUSTMENT
NOTICE:
This transmission requires Toyota Genuine ATF WS.
After servicing the transmission, you must follow the ATF adjustment procedure.
Maintain the vehicle in a horizontal position while adjusting the fluid level.
1. PRELIMINARY PROCEDURES
(a) w/ Trailer Towing System (w/ Transmission oil cooler
thermostat):
(1) Using compressed air, etc., blow dust off the thermostat cap
to clean it.
Pushed amount: 5.5 to 7.0 mm (0.217 to 0.276 in.)
Push the shaft until the screwdriver contacts the step inside the
cap.
HINT:
Pin diameter: 1.0 to 1.8 mm (0.0394 to 0.0709 in.)
2. BEFORE FILLING TRANSMISSION
When you have replaced the entire transmission, transmission pan, drain plug, valve body and/or
torque converter, proceed to the "TRANSMISSION FILL" procedures.
When you have replaced the transmission hose and/or output shaft oil seal, proceed to the "FLUID
TEMPERATURE CHECK" procedures.
3. TRANSMISSION FILL
AB60E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст