Toyota Tundra (2015 year). Manual — part 667
(d) Turn the torque converter and align the matchmarks on the
Text in Illustration
*a
Matchmark
NOTICE:
Do not push on the torque converter when aligning the
matchmarks.
(e) Using a vernier caliper and a straightedge, measure dimension B
shown in the illustration and check that B is greater than A
measured in the first step.
Standard distance:
B = A + 1 mm (0.0394 in.) or more
2. INSTALL TRANSMISSION CONTROL CABLE BRACKET
(a) Install the bracket with the 2 bolts.
Torque:
12 N·m {122 kgf·cm, 9ft·lbf}
3. INSTALL WIRE HARNESS CLAMP BRACKET
(a) Install the front bracket LH with the bolt.
Torque:
8.0 N·m {82 kgf·cm, 71in·lbf}
(b) Install the rear bracket LH with the bolt.
Torque:
29 N·m {296 kgf·cm, 21ft·lbf}
(c) Install the rear engine bracket with the bolt.
Torque:
8.0 N·m {82 kgf·cm, 71in·lbf}
4. INSTALL PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY
(a) Install the bracket with the bolt.
Torque:
20 N·m {204 kgf·cm, 15ft·lbf}
AB60F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
5. INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/o
Trailer Towing System)
(a) Coat 4 new O-rings with ATF.
(b) Install the 4 O-rings, transmission oil cooler spacer and
transmission oil cooler to the automatic transmission assembly
with the 3 bolts.
Torque:
21 N·m {214 kgf·cm, 15ft·lbf}
6. INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/
Trailer Towing System)
(a) Coat 4 new O-rings with ATF.
(b) Install the 4 O-rings, transmission oil thermostat and
transmission oil cooler to the automatic transmission assembly
with the 3 bolts.
Torque:
21 N·m {214 kgf·cm, 15ft·lbf}
7. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
Clutch spline grease:
Toyota Genuine Clutch Spline Grease or equivalent
Maximum grease amount
Approximately 1 g (0.0353 oz.) Centerpiece
Text in Illustration
*1
Torque Converter Centerpiece
AB60F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
*2
Crankshaft
(b) Confirm that the 2 knock pins are on the transaxle contact
Torque:
for 17 mm head bolt A -
71 N·m {724 kgf·cm, 52ft·lbf}
for 14 mm head bolt B -
37 N·m {377 kgf·cm, 27ft·lbf}
8. CONNECT NO. 2 WATER BY-PASS PIPE (w/o Towing Hitch)
(a) Connect the 2 water by-pass hoses with the 2 clips and install
the water by-pass pipe with the bolt.
Torque:
18 N·m {184 kgf·cm, 13ft·lbf}
Text in Illustration
*a
Stopper
*b
RH Side
NOTICE:
9. CONNECT NO. 2 WATER BY-PASS PIPE (w/ Towing Hitch)
AB60F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
(a) Connect the 2 oil cooler hoses to the transmission oil cooler.
Text in Illustration
*a
Paint Mark
NOTICE:
the water by-pass pipe with the bolt.
Torque:
18 N·m {184 kgf·cm, 13ft·lbf}
Text in Illustration
*a
Stopper
*b
RH Side
NOTICE:
10. CONNECT BREATHER PLUG HOSE
(a) Connect the 3 breather plug hoses to the harness clamp bracket.
11. CONNECT WIRE HARNESS AND CONNECTOR
AB60F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст