Toyota Tundra (2015 year). Manual — part 262
OK
(a) Remove the reservoir tank cap and strainer.
(b) Disconnect the A3 switch connector.
(c) Measure the resistance according to the value(s) in the table below.
HINT:
A float is placed inside the reservoir. Its position can be changed by increasing or decreasing the brake
fluid level.
Standard Resistance:
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED CONDITION
1 (+) - 2 (E)
Float up (Switch OFF)
10 kΩ or higher
1 (+) - 2 (E)
Float down (Switch ON)
Below 1 Ω
HINT:
If the result is as specified, adjust the brake fluid level to the MAX level after measuring the resistance.
NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR
SUB-ASSEMBLY
7.
CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL
WARNING SWITCH)
BRAKE CONTROL: VEHICLE STABILITY CONTROL SYSTEM: Br...
OK
(a) Disconnect the J28 meter connector.
(b) Disconnect the A3 switch connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
J28-14 (SW) - A3-1 (+)
Always
Below 1 Ω
J28-14 (SW) - Body ground
Always
10 kΩ or higher
A3-2 (E) - Body ground
Always
Below 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
8.
INSPECT COMBINATION METER
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON and the Techstream on.
.
Combination Meter
TESTER DISPLAY
TEST PART
CONTROL
RANGE
DIAGNOSTIC NOTE
BRAKE CONTROL: VEHICLE STABILITY CONTROL SYSTEM: Br...
OK
TESTER DISPLAY
TEST PART
CONTROL
RANGE
DIAGNOSTIC NOTE
Indicat. Lamp
Brake
Brake warning
light
ON or OFF
Perform the test with the vehicle stopped and engine
idling
(d) Check that the BRAKE warning light turns on and off in the combination meter using Techstream.
OK:
The BRAKE warning light turns on and off in accordance with the Techstream operation.
NG
GO TO METER / GAUGE SYSTEM
OK
REPLACE VSC ACTUATOR ASSEMBLY
9.
INSPECT PARKING BRAKE SWITCH ASSEMBLY
(a) Disconnect the A5 switch connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
SWITCH CONDITION
SPECIFIED CONDITION
1 - Switch body ground
Parking brake switch ON
(Switch pin released)
Below 1 Ω
1 - Switch body ground
Parking brake switch OFF
(Switch pin pushed in)
10 kΩ or higher
NG
REPLACE PARKING BRAKE SWITCH ASSEMBLY
10.
CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - PARKING BRAKE SWITCH)
BRAKE CONTROL: VEHICLE STABILITY CONTROL SYSTEM: Br...
(a) Disconnect the A17 ECU connector.
(b) Disconnect the A5 switch connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
A17-14 (PKB2) - A5-1
Always
Below 1 Ω
A17-14 (PKB2) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE VSC ACTUATOR ASSEMBLY
BRAKE CONTROL: VEHICLE STABILITY CONTROL SYSTEM: Br...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст