Toyota Tundra (2015 year). Manual — part 2148
(a) Disconnect the W3 ECU connector.
(b) Disconnect the W7 switch connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
W3-1 (UP) - W7-6 (UP)
Always
Below 1 Ω
W3-2 (DWN) - W7-5 (DWN)
Always
Below 1 Ω
W3-6 (OPN) - W7-4 (OPN)
Always
Below 1 Ω
W3-7 (CLS) - W7-3 (CLS)
Always
Below 1 Ω
W7-6 (UP) - Body ground
Always
10 kΩ or higher
W7-5 (DWN) - Body ground
Always
10 kΩ or higher
W7-3 (CLS) - Body ground
Always
10 kΩ or higher
W7-4 (OPN) - Body ground
Always
10 kΩ or higher
W7-7 (E) - Body ground
Always
Below 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE SLIDING ROOF DRIVE GEAR
SUB-ASSEMBLY (SLIDING ROOF ECU)
Last Modified: 9-16-2014
6.6 J
Doc ID: RM0000030NW00QX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
WIRING DIAGRAM
INSPECTION PROCEDURE
PROCEDURE
1.
READ VALUE USING TECHSTREAM (IGNITION SWITCH SIGNAL)
(a) Use the Data List to check if the ignition switch signal is functioning properly
.
Sliding Roof
TESTER DISPLAY
TEST PART
CONTROL RANGE
DIAGNOSTIC
NOTE
Ignition (MPX)
Ignition switch signal (MPX signal)/ON or
OFF
ON: Ignition switch
ON
OFF: Ignition switch
off
-
Ignition (Direct
Signal)
Ignition switch signal/ON or OFF
ON: Ignition switch
ON
OFF: Ignition switch
-
OK
TESTER DISPLAY
TEST PART
CONTROL RANGE
DIAGNOSTIC
NOTE
off
OK:
GO TO STEP 2
OK
REPLACE SLIDING ROOF DRIVE GEAR
SUB-ASSEMBLY (SLIDING ROOF ECU)
2.
INSPECT FUSE (S/ROOF, ECU-IG No.2)
(a) Remove the S/ROOF and ECU-IG No.2 fuses from the main body ECU.
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
S/ROOF fuse
Always
Below 1 Ω
ECU-IG No.2 fuse
Always
Below 1 Ω
NG
REPLACE FUSE
3.
CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BATTERY AND BODY
GROUND)
(a) Disconnect the W3 ECU connector.
(b) Measure the voltage according to the value(s) in the table
below.
Standard voltage :
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
W3-9 (IG) - Body ground Ignition switch ON 11 to 14 V
W3-9 (IG) - Body ground Ignition switch off Below 1 V
W3-10 (B) - Body ground Always
11 to 14 V
(c) Measure the resistance according to the value(s) in the table
below.
Standard resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
W3-8 (E) - Body ground
Always
Below 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE SLIDING ROOF DRIVE GEAR
SUB-ASSEMBLY (SLIDING ROOF ECU)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст