Toyota Tundra (2015 year). Manual — part 1797
(h) Tighten the 3 bolts in several steps in the sequence shown in
the illustration.
Torque:
47 N·m {479 kgf·cm, 35ft·lbf}
(i) Temporarily install the fluid coupling bracket with the 4 bolts.
Standard Bolt:
ITEM
LENGTH
THREAD DIAMETER
Bolt A
70 mm (2.76 in.)
8 mm (0.315 in.)
Bolt B
80 mm (3.15 in.)
10 mm (0.394 in.)
(j) Temporarily install the belt tensioner with the standard bolt
and 6 mm hexagon bolt.
(k) Tighten the 8 bolts labeled 4 to 11 in several steps in the
sequence shown in the illustration.
Torque:
47 N·m {479 kgf·cm, 35ft·lbf}
(l) Tighten the 23 bolts and nut labeled 12 to 35 in several steps in the sequence shown in the illustration.
3UR-FBE LUBRICATION: OIL PUMP: INSTALLATION; 2015 MY Tu...
Torque:
23 N·m {235 kgf·cm, 17ft·lbf}
NOTICE:
After the installation, if the seal packing has seeped out at the areas labeled A shown in the illustration,
wipe it off.
3. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
(a) Install 5 new gaskets to the camshaft bearing caps (No. 2,
No. 3).
(b) Install the gasket to the cylinder head cover.
NOTICE:
Remove any oil from the contact surface.
(c) Apply seal packing as shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or
equivalent
NOTICE:
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten
the bolts within 15 minutes after applying seal packing.
(d) Install the cylinder head cover washer with a new seal and
the 14 bolts.
Torque:
for bolt A -
21 N·m {214 kgf·cm, 15ft·lbf}
except bolt A -
12 N·m {122 kgf·cm, 9ft·lbf}
NOTICE:
Do not start the engine for at least 2 hours after the
installation.
3UR-FBE LUBRICATION: OIL PUMP: INSTALLATION; 2015 MY Tu...
4. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH
(a) Install 5 new gaskets to the camshaft bearing caps. (No. 1,
No. 3).
(b) Install the gasket to the cylinder head cover.
NOTICE:
Remove any oil from the contact surface.
(c) Apply seal packing as shown in the illustration.
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or
equivalent
NOTICE:
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten
the bolts within 15 minutes after applying seal packing.
(d) Install the cylinder head cover washer with a new seal and
the 14 bolts.
Torque:
for bolt A -
21 N·m {214 kgf·cm, 15ft·lbf}
except bolt A -
12 N·m {122 kgf·cm, 9ft·lbf}
NOTICE:
Do not start the engine for at least 2 hours after the
installation.
(e) Install the noise filter to the cylinder head cover with the
bolt.
Torque:
7.0 N·m {71 kgf·cm, 62in·lbf}
5. INSTALL IGNITION COIL ASSEMBLY
(a) Install the 8 ignition coils with the 8 bolts.
Torque:
10 N·m {102 kgf·cm, 7ft·lbf}
3UR-FBE LUBRICATION: OIL PUMP: INSTALLATION; 2015 MY Tu...
6. INSTALL CRANKSHAFT PULLEY
(b) Using SST, install the pulley set bolt.
SST: 09213-70011
SST: 09330-00021
Torque:
300 N·m {3059 kgf·cm, 221ft·lbf}
7. CONNECT WIRE HARNESS CLAMP BRACKET
(a) Connect the wire harness clamp bracket to the timing chain cover sub-assembly with the bolt.
Torque:
8.0 N·m {82 kgf·cm, 71in·lbf}
8. INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
(a) Install the No. 1 idler pulley sub-assembly with the bolt.
Torque:
43 N·m {438 kgf·cm, 32ft·lbf}
9. INSTALL WATER PUMP PULLEY
(a) Temporarily install the water pump pulley with the 4 bolts.
(b) Using SST, hold the water pump pulley and tighten the 4 bolts.
SST: 09960-10010
09962-01000
09963-01000
Torque:
21 N·m {214 kgf·cm, 15ft·lbf}
10. INSTALL WATER INLET HOUSING
(a) Install a new gasket to the timing chain cover sub-assembly.
Text in Illustration
*1
Gasket
(b) Install the water inlet housing with the 3 bolts.
Torque:
21 N·m {214 kgf·cm, 15ft·lbf}
3UR-FBE LUBRICATION: OIL PUMP: INSTALLATION; 2015 MY Tu...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст