Toyota Tundra (2015 year). Manual — part 1796
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002S4Z03MX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FBE LUBRICATION: OIL PUMP: REASSEMBLY; 2015 MY Tundra [08/2014 - ]
REASSEMBLY
1. INSTALL OIL PUMP RELIEF VALVE
(a) Coat the oil pump relief valve with engine oil.
(b) Install the relief valve and relief valve spring into the oil pump cover hole.
(c) Install the plug.
Torque:
53 N·m {540 kgf·cm, 39ft·lbf}
2. INSTALL OIL PUMP COVER
(a) Install the driven rotor, drive rotor and oil pump cover with
the 13 bolts.
Torque:
10 N·m {105 kgf·cm, 8ft·lbf}
3UR-FBE LUBRICATION: OIL PUMP: REASSEMBLY; 2015 MY Tun...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM000002S4U04IX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: 3UR-FBE LUBRICATION: OIL PUMP: INSTALLATION; 2015 MY Tundra [08/2014 - ]
INSTALLATION
1. INSTALL WATER INLET PIPE
(a) Apply soapy water to 2 new O-rings and install them to the
inlet pipe.
(b) Install the inlet pipe to the No. 1 heat exchanger cover.
2. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
(e) Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.
3UR-FBE LUBRICATION: OIL PUMP: INSTALLATION; 2015 MY Tu...
Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Apply seal packing as follows:
AREA
SEAL PACKING DIAMETER
APPLICATION POSITION FROM
INSIDE EDGE OF COVER
Continuous line
area
3.0 to 4.0 mm (0.118 to 0.157 in.)
2.5 mm (0.0984 in.)
Dashed line
area
6.4 mm (0.252 in.) or more, or within OK
area shown in illustration
7.0 mm (0.276 in.)
Diagonal line
area
3.0 to 4.0 mm (0.118 to 0.157 in.)
5.5 mm (0.217 in.)
3UR-FBE LUBRICATION: OIL PUMP: INSTALLATION; 2015 MY Tu...
NOTICE:
When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
Install the chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal
packing.
Do not start the engine for at least 2 hours after installing.
(f) Align the oil pump drive rotor spline and crankshaft as shown
in the illustration. Install the spline and chain cover to the
crankshaft.
(g) Temporarily install the timing chain cover with the 28 bolts
and nut.
Standard Bolt:
ITEM
LENGTH
THREAD DIAMETER
Bolt A
25 mm (0.984 in.)
8 mm (0.315 in.)
Bolt B
55 mm (2.17 in.)
8 mm (0.315 in.)
Bolt C
70 mm (2.76 in.)
8 mm (0.315 in.)
Bolt D
35 mm (1.38 in.)
10 mm (0.394 in.)
Bolt E
55 mm (2.17 in.)
10 mm (0.394 in.)
Bolt F
80 mm (3.15 in.)
10 mm (0.394 in.)
NOTICE:
Make sure that there is no oil on the bolt threads.
3UR-FBE LUBRICATION: OIL PUMP: INSTALLATION; 2015 MY Tu...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст