Toyota Tundra (2015 year). Manual — part 334
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000000W7Z0Q1X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: A760E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION SYSTEM: P0711; Transmission Fluid
Temperature Sensor "A" Performance; 2015 MY Tundra [08/2014 - ]
DTC
P0711
Transmission Fluid Temperature Sensor "A" Performance
DESCRIPTION
The ATF temperature sensor converts the fluid temperature into a resistance value for use by the ECM.
resistance decreases.
The ECM calculates the fluid temperature based on the voltage signal.
DTC
CODE
DTC DETECTION CONDITION
TROUBLE AREA
P0711
Either condition is met (2-trip detection logic):
(a) Certain monitor enabling conditions are met and the ATF
temperature is below 20°C (68°F).
(b) Certain monitor enabling conditions are met and the ATF
temperature is 110°C (230°F) or higher.
Transmission wire (No. 1 ATF
temperature sensor)
MONITOR DESCRIPTION
This DTC indicates that there is a problem with output from the Automatic Transmission Fluid (ATF) temperature
sensor and that the sensor itself is defective. The ATF temperature sensor converts the ATF temperature to an
electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects an
open or short in the ATF temperature sensor circuit or a fault in the ATF temperature sensor.
After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is
below 20°C (68°F) after running the vehicle for a certain period, the ECM interprets this as a fault, turns on the
MIL and stores the DTC.
When the ATF temperature is 110°C (230°F) or more and the engine coolant temperature takes 10 seconds or
more to reach 60°C (140°F) after a cold start, the ECM also determines this as a fault, turns on the MIL and
stores the DTC.
MONITOR STRATEGY
Related DTCs
P0711: ATF temperature sensor/Rationality check
Required sensors/Components
ATF temperature sensor
A760E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Duration
Condition (A), (B), (C) and (D): 3 seconds
Condition (E): Continuous
MIL operation
2 driving cycles
TYPICAL ENABLING CONDITIONS
All
The monitor will run whenever the following
DTCs are not present
P0712, P0713, P2740, P2742, P2743 (ATF temperature sensor
"A" circuit)
P0115, P0116, P0117, P0118, P011B (ECT (Engine Coolant
Temperature) sensor circuit)
P0110, P0111, P0112, P0113 (IAT (Intake air temperature)
sensor circuit)
U0100 (CAN communication system)
P2610 (Soak timer circuit)
Condition (A)
Duration time from engine start
12 seconds or more
ECT
-15°C (5°F) or higher
Permission flag for ATF temperature rationality check
ON
Time after engine start except for continuing shift position "N" or "P"*2
5 minutes or more
Accumulated driving time*1
75 seconds or more
Driving distance after engine start*3
4.7 km (3.0 miles) or more
ECT (12 seconds after engine start)
15°C (59°F) or higher
IAT*4
15°C (59°F) or higher
Soak time
5 hours or more
Condition (B)
Duration time from engine start
12 seconds or more
ECT
-15°C (5°F) or higher
Permission flag for ATF temperature rationality check
ON
Time after engine start except for continuing shift position "N" or "P"*2
21 minutes and 40 seconds or more
Accumulated driving time*1
140 seconds or more
Driving distance after engine start*3
9.0 km (5.6 miles) or more
ECT (12 seconds after engine start)
-10°C (14°F) or higher
IAT*4
-10°C (14°F) or higher
Condition (C)
A760E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Duration time from engine start
12 seconds or more
ECT
-15°C (5°F) or higher
Permission flag for ATF temperature rationality check
ON
Time after engine start except for continuing shift position "N" or "P"*2
30 minutes or more
Accumulated driving time*1
400 seconds or more
Driving distance after engine start*3
16.0 km (9.9 miles) or more
ECT (12 seconds after engine start)
-15°C (5°F) or higher
IAT*4
-15°C (5°F) or higher
Condition (D)
Duration time from engine start
12 seconds or more
ECT
-15°C (5°F) or higher
Permission flag for ATF temperature rationality check
ON
Time after engine start except for continuing shift position "N" or "P"*2
55 minutes or more
Accumulated driving time*1
750 seconds or more
Driving distance after engine start*3
27.0 km (16.8 miles) or more
Condition (E)
Duration time for ECT to reach 60°C (140°F)
10 seconds or more
ATF temperature (12 seconds after engine start)
110°C (230°F) or higher
ECT (12 seconds after engine start)
Below 35°C (95°F)
HINT:
*1: Following conditions are met
Engine speed - Turbine speed
50 rpm or more
Output speed
400 rpm or more
Throttle valve opening angle
5.5% or more
Shift position
Not "N" or "P"
Engine
Starting
However, accumulated driving time is cleared
-
When following condition met
-
Duration time from shift position "N" or "P"
300 seconds or more
*2: Time after engine start is cleared when following condition met
Duration time from shift position "N" or "P"
300 seconds or more
*3: Driving distance is cleared when following condition met
A760E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Duration time from shift position "N" or "P"
300 seconds or more
-
Duration time from shift position "N" or "P"
300 seconds or more
TYPICAL MALFUNCTION THRESHOLDS
When either condition below is met: Condition (A), (B), (C), (D) or (E)
Condition (A), (B), (C) and (D)
ATF temperature
Below 20°C (68°F)
Condition (E)
ATF temperature
110°C (230°F) or higher
COMPONENT OPERATING RANGE
Condition (A), (B), (C), (D) and (E)
ATF temperature
20°C (68°F) or higher, and below 110°C (230°F)
INSPECTION PROCEDURE
NOTICE:
Perform the universal trip to clear permanent DTCs
.
If DTCs P0711 and P2610 are output simultaneously, confirm that the ATF temperature is as specified in
"Normal Condition" using the Techstream first. When the ATF temperature is as specified in "Normal
Condition", perform troubleshooting for DTC P2610
.
1. DATA LIST
HINT:
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely
on these reference values when deciding whether a part is faulty or not.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the Techstream on.
(f) Enter the following menus: Powertrain / Engine and ECT / Data List.
A760E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст