Toyota Tundra (2015 year). Manual — part 1162
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
10.
Input the DTC: P0351, P0352, P0353, P0354, P0355, P0356, P0357 or P0358.
11.
Check the DTC judgment result.
TESTER
DISPLAY
DESCRIPTION
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
HINT:
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again.
12.
If no pending DTC is output, perform a universal trip and check for permanent DTCs
.
HINT:
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
13.
WIRING DIAGRAM
1UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0351-P0358; ...
1UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0351-P0358; ...
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when
malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was
moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other
data from the time the malfunction occurred.
PROCEDURE
1UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0351-P0358; ...
1.
INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
(a) Disconnect the ignition coil assembly connector.
(b) Measure the resistance according to the value(s) in the table
below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
D10-4 (GND) - Body ground
Always
Below 1 Ω
D25-4 (GND) - Body ground
Always
Below 1 Ω
D12-4 (GND) - Body ground
Always
Below 1 Ω
D23-4 (GND) - Body ground
Always
Below 1 Ω
D14-4 (GND) - Body ground
Always
Below 1 Ω
D21-4 (GND) - Body ground
Always
Below 1 Ω
D16-4 (GND) - Body ground
Always
Below 1 Ω
D19-4 (GND) - Body ground
Always
Below 1 Ω
(c) Turn the ignition switch to ON.
(d) Measure the voltage according to the value(s) in the table
below.
Standard Voltage:
TESTER CONNECTION
SWITCH
CONDITION
SPECIFIED
CONDITION
D10-1 (+B) - D10-4
(GND)
Ignition switch ON
11 to 14 V
D25-1 (+B) - D25-4
(GND)
Ignition switch ON
11 to 14 V
D12-1 (+B) - D12-4
(GND)
Ignition switch ON
11 to 14 V
D23-1 (+B) - D23-4
(GND)
Ignition switch ON
11 to 14 V
D14-1 (+B) - D14-4
(GND)
Ignition switch ON
11 to 14 V
D21-1 (+B) - D21-4
(GND)
Ignition switch ON
11 to 14 V
D16-1 (+B) - D16-4
(GND)
Ignition switch ON
11 to 14 V
D19-1 (+B) - D19-4
(GND)
Ignition switch ON
11 to 14 V
1UR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0351-P0358; ...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст