Toyota Tundra (2015 year). Manual — part 361
NG
REPLACE SHIFT SOLENOID VALVE S4
OK
REPAIR OR REPLACE TRANSMISSION WIRE
A760E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Last Modified: 9-16-2014
6.6 C
Doc ID: RM000000W8H0CEX
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: A760E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION SYSTEM: P0985,P0986; Shift Solenoid
"E" Control Circuit Low (Shift Solenoid Valve SR); 2015 MY Tundra [08/2014 - ]
DTC
P0985
Shift Solenoid "E" Control Circuit Low (Shift Solenoid Valve SR)
DTC
P0986
Shift Solenoid "E" Control Circuit High (Shift Solenoid Valve SR)
DESCRIPTION
solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated
safely. Also, the ECM stops sending current to the open or short-circuited solenoid
.
DTC
CODE
DTC DETECTION CONDITION
TROUBLE AREA
P0985
ECM detects a short in the solenoid valve SR circuit 2 times when
solenoid valve SR is operated (1-trip detection logic).
Short in shift solenoid
valve SR circuit
Shift solenoid valve SR
ECM
P0986
ECM detects an open in the solenoid valve SR circuit 2 times when
solenoid valve SR is not operated (1-trip detection logic).
Open in shift solenoid
valve SR circuit
Shift solenoid valve SR
ECM
MONITOR DESCRIPTION
These DTCs indicate an open or short in the shift solenoid valve SR circuit. When there is an open or short circuit
in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. When
the shift solenoid valve SR is ON, if its resistance is 8 Ω or less, the ECM determines there is a short in the shift
solenoid valve SR circuit.
When the shift solenoid valve SR is OFF, if its resistance is 100 kΩ or more, the ECM determines there is an open
in the shift solenoid valve SR circuit
.
MONITOR STRATEGY
Related DTCs
P0985: Shift solenoid valve SR/Range check (Low resistance)
P0986: Shift solenoid valve SR/Range check (High resistance)
Required sensors/Components
Shift solenoid valve SR
A760E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Duration
0.128 seconds or more
MIL operation
Immediately
TYPICAL ENABLING CONDITIONS
All
The monitor will run whenever the following DTCs are not present
None
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF
P0985: Range Check (Low Resistance)
Command to shift solenoid valve SR
ON
P0986: Range Check (High Resistance)
Command to shift solenoid valve SR
OFF
TYPICAL MALFUNCTION THRESHOLDS
P0985: Range Check (Low Resistance)
Shift solenoid valve SR resistance
8 Ω or less
P0986: Range Check (High Resistance)
Shift solenoid valve SR resistance
100 kΩ or more
COMPONENT OPERATING RANGE
Shift solenoid valve SR resistance
11 to 15 Ω at 20°C (68°F)
WIRING DIAGRAM
A760E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
INSPECTION PROCEDURE
NOTICE:
Perform the universal trip to clear permanent DTCs
.
HINT:
The shift solenoid valve SR is turned ON/OFF normally when the shift lever is in D:
ECM gear shift command
1st
2nd
3rd
4th
5th
6th
Shift solenoid valve SR
ON
ON
ON
ON
OFF
OFF
PROCEDURE
1.
INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SR)
(a) Disconnect the D83 transmission wire connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
TESTER CONNECTION
CONDITION
SPECIFIED CONDITION
A760E AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMIS...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст