Toyota Tundra (2015 year). Manual — part 802
MARK
THICKNESS
MARK
THICKNESS
80
1.79 to 1.81 mm (0.0705
to 0.0712 in.)
22
2.21 to 2.23 mm (0.0871
to 0.0877 in.)
82
1.81 to 1.83 mm (0.0713
to 0.0720 in.)
24
2.23 to 2.25 mm (0.0878
to 0.0885 in.)
84
1.83 to 1.85 mm (0.0721
to 0.0728 in.)
26
2.25 to 2.27 mm (0.0886
to 0.0893 in.)
86
1.85 to 1.87 mm (0.0729
to 0.0736 in.)
28
2.27 to 2.29 mm (0.0894
to 0.0901 in.)
88
1.87 to 1.89 mm (0.0737
to 0.0744 in.)
30
2.29 to 2.31 mm (0.0902
to 0.0909 in.)
90
1.89 to 1.91 mm (0.0745
to 0.0751 in.)
32
2.31 to 2.33 mm (0.0910
to 0.0917 in.)
92
1.91 to 1.93 mm (0.0752
to 0.0759 in.)
34
2.33 to 2.35 mm (0.0918
to 0.0925 in.)
94
1.93 to 1.95 mm (0.0760
to 0.0767 in.)
36
2.35 to 2.37 mm (0.0926
to 0.0933 in.)
96
1.95 to 1.97 mm (0.0768
to 0.0775 in.)
38
2.37 to 2.39 mm (0.0934
to 0.0940 in.)
98
1.97 to 1.99 mm (0.0776
to 0.0783 in.)
40
2.39 to 2.41 mm (0.0941
to 0.0948 in.)
00
1.99 to 2.01 mm (0.0784
to 0.0791 in.)
42
2.41 to 2.43 mm (0.0949
to 0.0956 in.)
02
2.01 to 2.03 mm (0.0792
to 0.0799 in.)
44
2.43 to 2.45 mm (0.0957
to 0.0964 in.)
04
2.03 to 2.05 mm (0.0800
to 0.0807 in.)
46
2.45 to 2.47 mm (0.0965
to 0.0972 in.)
06
2.05 to 2.07 mm (0.0808
to 0.0814 in.)
-
-
13. INSTALL BEARING CAP
(a) Align the matchmarks on the cap and carrier.
Text in Illustration
*a
Matchmark
(b) Install the 4 bolts.
Torque:
DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 3UR-...
205 N·m {2090 kgf·cm, 151ft·lbf}
HINT:
After rotating the ring gear 5 times or more, recheck the backlash.
14. INSPECT DIFFERENTIAL RING GEAR RUNOUT
0.05 mm (0.00197 in.)
If the runout is not within the specification, replace the ring gear.
15. INSPECT TOTAL PRELOAD
(a) Using a torque wrench, measure the preload with the teeth of
the drive pinion and ring gear in contact.
Standard total preload (at starting):
BEARING
SPECIFIED CONDITION
New
Standard drive pinion preload plus 0.22 to 0.41 N*m (3 to
4 kgf*cm, 2 to 3 in.*lbf)
Reused
Standard drive pinion preload plus 0.19 to 0.38 N*m (2 to
3 kgf*cm, 2 to 3 in.*lbf)
16. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION
(a) Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.
(b) Turn the companion flange in both directions to inspect the ring gear for proper tooth contact.
DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 3UR-...
Text in Illustration
*a Proper Contact
*b Heel Contact
*c Face Contact
*d
Select an adjusting washer that will shift the drive
pinion closer to the ring gear (*b, *c)
*e Toe Contact
*f Flank Contact
*g
Select an adjusting washer that will shift the drive
pinion away from the ring gear (*e, *f)
-
-
If the teeth are not contacting properly, use the following table to select a proper washer for
correction.
Text in Illustration
*1
Plate Washer
Washer thickness:
THICKNESS
THICKNESS
0.99 to 1.01 mm (0.0390 to 0.397 in.)
1.265 to 1.285 mm (0.0498 to 0.0505 in.)
1.015 to 1.035 mm (0.0400 to 0.0407 in.)
1.29 to 1.31 mm (0.0508 to 0.0515 in.)
1.04 to 1.06 mm (0.0410 to 0.0417 in.)
1.315 to 1.335 mm (0.0518 to 0.0525 in.)
1.065 to 1.085 mm (0.0420 to 0.0427 in.)
1.34 to 1.36 mm (0.0528 to 0.0535 in.)
DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 3UR-...
THICKNESS
THICKNESS
1.09 to 1.11 mm (0.0430 to 0.0437 in.)
1.365 to 1.385 mm (0.0538 to 0.0545 in.)
1.115 to 1.135 mm (0.0439 to 0.0446 in.)
1.39 to 1.41 mm (0.0548 to 0.0555 in.)
1.14 to 1.16 mm (0.0449 to 0.0456 in.)
1.415 to 1.435 mm (0.0557 to 0.0564 in.)
1.165 to 1.185 mm (0.0459 to 0.0466 in.)
1.44 to 1.46 mm (0.0567 to 0.0574 in.)
1.19 to 1.21 mm (0.0469 to 0.0476 in.)
1.465 to 1.485 mm (0.0577 to 0.0585 in.)
1.215 to 1.235 mm (0.0479 to 0.0486 in.)
1.49 to 1.51 mm (0.0587 to 0.0594 in.)
1.24 to 1.26 mm (0.0489 to 0.0496 in.)
-
17. REMOVE REAR DRIVE PINION NUT
(a) Using SST to hold the companion flange, remove the nut.
SST: 09330-00021
09330-00030
18. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
19. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL
(a) Using SST and a plastic-faced hammer, tap in a new oil seal
until its surface is flush with the differential carrier end.
SST: 09316-12010
SST: 09649-17010
Standard oil seal depth:
-0.45 to 0.45 mm (-0.0177 to 0.0177 in.)
Text in Illustration
*a
Vinyl Tape
HINT:
Connect 2 SST with vinyl tape.
DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 3UR-...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст