Toyota Tundra (2015 year). Manual — part 803
(a) Using SST, install the companion flange.
SST: 09950-30012
09951-03010
09953-03010
09954-03010
09956-03030
SST: 09955-03050
Text in Illustration
*a
Turn
*b
Hold
SST: 09330-00021
09330-00030
Torque:
304 N·m {3100 kgf·cm, 224ft·lbf}
21. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD
Standard preload (at starting):
BEARING
SPECIFIED CONDITION
New
1.80 to 3.17 N*m (19 to 32 kgf*cm, 16 to 28 in.*lbf)
Reused
1.62 to 2.25 N*m (17 to 22 kgf*cm, 15 to 19 in.*lbf)
If the preload is not within the specification, refer to the tables in
the "INSPECT DIFFERENTIAL DRIVE PINION PRELOAD (with
22. INSPECT TOTAL PRELOAD
DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 3UR-...
(a) Using a torque wrench, measure the preload with the teeth of
the drive pinion and ring gear in contact.
Standard total preload (at starting):
BEARING
SPECIFIED CONDITION
New
Standard drive pinion preload plus 0.22 to 0.41 N*m (3 to
4 kgf*cm, 2 to 3 in.*lbf)
Reused
Standard drive pinion preload plus 0.19 to 0.38 N*m (2 to
3 kgf*cm, 2 to 3 in.*lbf)
23. INSPECT DIFFERENTIAL RING GEAR BACKLASH
0.10 to 0.20 mm (0.00394 to 0.00787 in.)
HINT:
Perform the measurements at 3 or more positions around the
side bearing preload or repair as necessary.
24. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY
Text in Illustration
*a
72 mm (2.83 in.)
Maximum runout:
RUNOUT
SPECIFIED CONDITION
Vertical runout
0.10 mm (0.00394 in.)
Lateral runout
0.10 mm (0.00394 in.)
If the runout is more than the maximum, replace the
companion flange.
DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 3UR-...
25. STAKE REAR DRIVE PINION NUT
(a) Using a chisel and hammer, stake the nut.
DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 3UR-...
Last Modified: 9-16-2014
6.6 A
Doc ID: RM00000174J018X
Model Year: 2015
Model: Tundra
Prod Date Range: [08/2014 - ]
Title: DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 3UR-FE, 3UR-FBE): INSTALLATION; 2015 MY
Tundra [08/2014 - ]
INSTALLATION
1. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY
(b) Install a new gasket and the differential carrier with the 10 washers and 10 nuts.
Torque:
72 N·m {734 kgf·cm, 53ft·lbf}
NOTICE:
(a) Install the rear axle shaft LH
.
3. INSTALL REAR AXLE SHAFT RH
HINT:
Use the same procedure described for the LH side.
4. INSTALL PROPELLER SHAFT ASSEMBLY
(a) Install the propeller shaft for 2WD
.
(b) Install the propeller shaft for 4WD
.
5. ADD DIFFERENTIAL OIL
6. INSTALL REAR WHEEL
(a) Install the rear wheels.
Torque:
for aluminum wheel -
131 N·m {1336 kgf·cm, 97ft·lbf}
for steel wheel -
209 N·m {2131 kgf·cm, 154ft·lbf}
DIFFERENTIAL: DIFFERENTIAL CARRIER ASSEMBLY (for 3UR-...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст